8024F Upgrade Path
Hi there,I have inherited some Dell 8024F switches and am looking to upgrade from 3.1.4.5 to 5.1.2.3.I assume there will be an upgrade path for these, but I am struggling to find it. Anyone?Should...
View ArticleM6348 Stacking with CX4 to PowerConnect 70XX switches w/ CX4 expansion modules.
Hi there, I currently have a stack of Dell PowerConnect 7048P switches. They are using the CX4 Stacking Cables, and have the expansion modules installed. So I have 4 Stacking cables going out from...
View ArticlePowerconnect 8024f with BGP router
We want to connect BGP routers via Powerconnect 8024f switch.The topology is followed. Optical Link copper linkBGP router 1...
View ArticleN2024P POE issue
I replaced an older POE switch with a new Dell N2024P. The Switch had three Cisco LAP1242G Access Points connected them.After connecting the access points to the new switch they were all in a Disabled...
View Articleomnm 5.3 not showing and traffic
how do i enable my powerconnect switches to show traffic with onmn 5.3. i have the device addedd. i r-click the device - register with traffic analyzer but still nothing. do i need to enable slfow or...
View ArticleOMNM 5.3 sp2 can't authenticate SSHv2 with radius
I use putty to connect switch with radius user and it is successfully connect to it but when I am using OMNM discovery for switch using radius user, it timeout and get error. I am using PC6224 switch...
View ArticleReset AP105 to factory settings
We purchased 16 AP105's from Dell a couple years ago (before my time). We recently acquired two used identical models. How do I reset them to factory settings so our current virtual controller can see...
View Articleonmn 5.3 telnet credentials do not work
i keep getting no credentials found for telnet /ssh when i try to backup my config using ONMN 5.3i have the switch added as a managed resource using snmp. however i tried to configure the telnet...
View ArticlePowerconnect M6220 10G optical transceiver inserted/removed from IntfNotPresent
We have two M6220 switches stacked in an M1000e chassis filled with 14 M520's and one M910 with the embedded 10G BCM57810 NIC as well as an Intel I350 1Gb mezz card. Keep in mind the onboard 10G card...
View ArticleDell PowerConnect 6024F get mac by ip with arp and more option
Hello DELL Community members.I hava a little question, and hoping to find some answers here ;) I am writing a little script, and in this script I need to get mac address that is bind to ip-address by...
View ArticleN2048 SNMP and LLDP issue
My Dell N2048 switches are returning the remote lldp system ip address in reverse. Did I screw someting up ? I'm using snmp version 2.
View ArticleOMNM 5.3 what is MIB browser
hello can someone explain what the following is and what its used for in OMNM 5.3under managed resources > direct access > mib browser (PowerConnect Switch)
View ArticleLink Aggregation and VLAN Trunking
I've configured 2 switches with Link Aggregates between them. The Access ports are part of VLAN 10 but are no longer communicating via the NEWLY created LAG's. Do LAG's pass only a single VLAN or is...
View ArticleDell N2000 Series Logging Possibilities
Hi.This is a fairly simple question:The PCI-DSS requirements specifies that you have to audit all administrative commands on all network switches within the PCI scope.The old PowerConnect does not...
View Articleupdate firmware on PC8024-k blade chassis stack?
I attempted to update the firmware on a PC8024-k 2 switch stack to 5.1.5.1. After the update this is what I get:unit image1 image2 current-active next-active---- ----------- -----------...
View ArticleDHCP-Server binding to VLANs on PowerConnect 5548
Hi,just logged on to the community as we are new owners of Dell PowerConnect 5548 switches.I read the manual and searched the forums, but I can not find out, how I can bind DHCP-server I configure on...
View ArticleM8024 speed only 1G with BRCM 10GbE 2P 57810S-k Mezz
We received some M820 blades recently which have BRCM 10GbE 2P 57810S-k Mezz to M8024 (original not -k version) and they are only getting 1G speed. The OS is Dell-installed ESXi 5.1 latest update...
View ArticleDell PowerConnect 7048P Stack Questions
Hello,I have two 7048P L3 switches that I'd like to stack but I"m unsure on how it works. Both switches have the same firmware.1. Do they both have to have the same configuration running on both for...
View ArticleDell Force 10 MXL 10/40GbE switch
Need some help if someone knows how to to setup this switch. I have a M1000E chassis with this Dell Force 10 MXL installed. The 10GBase-T Module is installed. I setup the tengigabitethernet 0/1 to...
View ArticleConnecting dual network access points to a 7048P
Previously our core switch was a 3 Com 4500 series which our access points connected to via power connectors these AP's are from HP and basically they are capable of broadcasting 2 SSIDs one was for...
View Article