authentication open for aaa debugging on Powerconnect
HiWe are setting up switches to use RADIUS. In order to check if all clients authenticate as we think they will do, it would be nice to issue a command like they have in Cisco switches "authentication...
View Article2 vlans on one port DHCP problem
I'm currently working on a project where I need to separate Guests to our network from our internal network. Right now I have 2 Cisco aironet 1142 APs connected to a dell 3548p switch. My win server...
View ArticleTrouble connecting to the CLI / console on a pair of Dell Force10 S25
I've obtained a pair of Dell Force10 S25 switches and I'm trying to log into the switches to test / reset them. I have no luck accessing the CLI on either of the switches.I'm using HyperTerminal,...
View ArticleHelp needed with NIC Teaming on Windows Storage Server 2008R2 through...
We have a Dell Powervault NX with 2 Broadcom NICs (4 ports) as our primary file server connected to our LAN through a PowerConnect 2724. I wanted to increase throughput to it so I began looking into...
View ArticleN4032 LAG MTU
Hello together,We want use MTU of 9000 an the PowerConnect 8xxx Series ( N4032 )We did enabled the command in the console:“system jumbo mtu 9216”How can we set the MTU of a LAG member?vMotion doens not...
View ArticleOnly one SFlow Collector can receive data?
Hello,I have configured two SFlow collector at 8132FHowever, there only first one (Receiver Index 1) can receiving SFlow, the another cannot. How to config both (all) collector can collect SFlow at...
View ArticleDell powerconnect 6248P voice vlan with cisco ip phones
Hi,i have configured dell powerconnect 6248p with data and voice vlan in the same port and i am connecting Cisco ip-phone on that port, my phone is working but when i am connecting my PC to the phone...
View ArticleAuthentication bypass if RADIUS goes down
Is it possible to configure PowerConnect switches, so that they authenticate devices on a critical VLAN, if there is no connection to the RADIUS server ?By critical VLAN, I mean corporate access VLAN,...
View ArticleDell 8132f : Get serial number of QSFP 40G
Dear Dell Support,Please let me know how to get Serial number of QSFP 40G that i did plug them into switch and make them as stack-port.Best regards,T.
View ArticleNeed help with basic S4810 install for testing a realtime san failure - we...
Long story short, new equallogic san in 3 locations, all identical. Worked fine in first install, duplicate failures in second and third.Our new HP switches are unsupported, so I need to provide...
View ArticleDell N2024 Switch VS 0GF76J SFP Transceivers
Hi,I've a question regarding Dell N2024 switches and 0GF76J transceivers. I bought 2 of this switch model and 4 of this transceiver model from a supplier. The optical fiber ports of this switch are...
View ArticleDell 5548 Force 10 configuration CLI
I have inherited a Dell 5548 that I am not able to access the web interface on. Through CLI, I have discovered two VLANs are configured. 4094 is set as the default but down with line protocol down as...
View ArticleN3024 view port utilization, not statistics
Is there a way to see port utilization in "real" time ?Similar to Cisco's 5 minute thing in CLI.I can see statistics on the Web Administrator but that tells me nothing.I don't really care how many...
View ArticlePort/VLAN config on MXL switches
I'm not a network engineer, but am trying to set one port on my MXL switch to a VLAN which will route traffic out from virtual machines to a local compute network. It's port Te 0/52 on the back of the...
View ArticleErrors on Dell N3000 log : DRIVER[112060908]: broad_hpc_drv.c(4362) 22493 %%...
I am getting a tons of this on our Core switch N3000, anyone? What does this mean?
View ArticleHow to show Dell Powerconnect running config without breaks in the cli
Hello,I usually work with Cisco switches where I can type "term len 0" before executing "show run" to get a full output of the running config without any pause/breaks. Unfortunately, this command...
View ArticleIs it possible to connect 8024f and 8132f?
Hi,We have 2 storage networks on the same IP range and no conflicting IP's. As part of a consolidation we are trying to make the 2 equalogic SAN's on each portion available to all esx hosts. Currently...
View ArticlePowerConnect 3524 MTU
I want to pass MTU of 1548 for MPLS and VLANs and manual only makes reference to ipv6 set mtu {ethernet interface | port-channel port-channel-number} MTU BYTES. Thanks in advance.
View ArticleJumbo frames best practise
hi there,I am looking to use a pair of N3048s in a branch office as both the network core and for iSCSI (connected to a new equallogic).As I understand it you can't set jumbo frames on a single port...
View ArticleLink Aggregation between Powerconnect 7048 Stack and Force 10 S55 Stack
Hi all,I am trying to connect a 7048 stack with a S55 stack (2 switches in each stack). I would like to use two ports (one from each switch) from each stack to connect to the other. Can anyone help me...
View Article