Anyone know if there are any setting to specify traffic shaping on the Dell PowerConnect 2816 or 2824 web managed switches?
↧
traffic shaping on PowerConnect 28XX series
↧
5448 is missing commands
When I try to configure a stactic route in the switch I get the following. I'm wondering if the image is corrupt except I have two of this model with the same trouble.
aspswt1(config)# ip route x.x.x.x /24 x.x.x.x
% Unrecognized command
a listing of the commands shows:
aspswt1(config)# ip
access-list This command creates an ACL, which perform
classification on layer 3 fields and enters to
ip-access configuration mode.
default-gateway Specify default gateway
dhcp Acquire IP address from DHCP server
domain-lookup To enable the IP Domain Naming System
domain-name To define a default domain names that the software
uses to complete unqualified host names
host To define static host name-to-address mapping in the
host cache
http Specify the HTTP server configuration
https Specify the HTTPS server configuration
igmp Global IGMP configuration commands
name-server To set the available name servers, use the ip
name-server global configuration command.
ssh Global Secure Shell protocol configuration subcommands
telnet Telnet server configuration
Software is:
SW version 2.0.0.46 ( date 14-Apr-2011 time 13:10:53 )
Boot version 2.0.0.0 ( date 12-Nov-2008 time 12:56:52 )
HW version 00.00.02
↧
↧
how to check fastport setting in powerconnect 3348 /3324
hello,
I am new with dell switches,
I am logged into web console of powerconnect 3348 and trying to find out STP fastport setting,
want to make sure that its enabled.
Thanks
↧
Double 802.1x radius depending on vlan
Hello all
i need to build an enviroment where i should have 2 diffrents radius (Windows IAS) that checks that host have been already added to 2 differents and isolated domains)
Each domain are in different VLANs
I have got running 1 radius
dot1x system-auth-control
aaa authentication dot1x default radius
aaa authorization network default radius
radius-server attribute 4 10.124.14.40
radius-server source-ip 10.124.14.40
radius-server key "passradius"
radius-server host auth 10.124.14.3
name "Default-RADIUS-Server"
exit
But i don´t know if its possible add the second one profile and how achive this problem
Thxs a lot in advice
Nacho
↧
Disabling Interface ports
Hi, We have two Dell Power Connect 6224 switches and we are trying to disable a couple of ports to prevent them being active should a network cable be plugged in. What is the best way to do this?
Kind regards
Paul
↧
↧
SNMP Monitoring of VLANs (Some More)
I am trying to monitor traffic utilization on VLAN using SNMP. When I look at the SNMP walk, the counters for the VLANs are showing zero across the board. I've searched through the forum and found server cases of the issue, but no actual fix or even response from an employee.
Is this still a known issue with PowerConnect switches?
My Switch is a PowerConnect 2848.
What I'm getting back from SNMP:
iso.3.6.1.2.1.2.2.1.10.100000 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100001 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100002 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100003 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100004 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100005 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100006 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100007 = Counter32: 0
iso.3.6.1.2.1.2.2.1.10.100008 = Counter32: 0
↧
PC 6248: Getting DHCP address for wrong subnet.
I recently inherited a Dell PowerConnect 6248 which I'm not that familiar with, and I'm trying to use it as a Layer3 switch.
I have a VLAN 10 with an associated network of 10.10.10.0/24 and a VLAN 11 with an associated network of 10.10.11.0/24.
When I have statically assigned addresses on clients on ports configured for these VLANs. I can ping other subnets, and traffic is routed properly.
I also have IP helper configured globally pointing to my DHCP server, and I have DHCP scopes setup for the networks associated with VLAN 10 and 11.
When I connect a device to a port configured with VLAN 10, I receive a DHCP address in the 10.10.10.0/24 network.
However, when I connect a device to a port configured with VLAN 11, I receive a DHCP address also in the 10.10.10.0/24 when it should be in the 10.10.11.0/24 network.
Both VLANs, routes, and DHCP scopes appear to be properly configured everywhere. Again, when clients use statically assigned addresses for their appropriate VLANs and networks, traffic is routed normally. But I am getting DHCP addresses for the wrong subnet for clients connected to VLAN 11.
Any help is greatly appreciated!
↧
Multiple Locations Routing
What i know so far.
3physical locations: Location1 / Location 2 / Location3
ICMP is allowed over through the VPN/Firewall. I can ping other devices, from Location1, that are on the Location 2 / Location3 LANs, just not my force10 stack
I can ping the switches locally (local LAN), but not from alternate sites. In Location1 I can ping or ssh to the Location1 Stack, But I can not Ping the Location 2 / Location3 stacks. I have to ssh to one of the servers in the other locations to ssh or ping the Stack.
I've never set this up before, any ideas? On the best way to do it?
Thanks,
Ron
↧
Pwerconnect 5448, Windows Server 2008 R2
Hello from France,
One of my project for a customer is to create a secure authentification via 802.1X. I chose to use freeradius.
But the customer didn't want to integrate a linux solution.
So I switched to Microsoft Windows server 2008 R2 and the NPS. I set up two solutions
First, a NAP. The solution works without any problems.
But the second, configuring dell powerconnect device to a authenticate via active active directory has not working. I found and tried many howtos on the web, but no one are compliant with my device.
someone have to deploy this solution with the NAP of Microsoft? Is there a POC from dell, which allow to solve it ?
Thank for your helps
Théo
↧
↧
PowerConnect 6224 iSCSI Enable
I am running a SAN off of a Power Connect 6224 and was going through the setups on the Power Connect. I noticed that the iSCSI was not enabled on the switch. Can I enable the iSCSI config while servers are accessing the SAN through the PC6224?
Just wondering if I need to shutdown all servers linked to the PC6224.
We only have one PC6224 switch right now, we will be purchasing another one soon for redundancy.
Thanks,
Ken
↧
PowerConnect 6248 stack frozen
Hello,
We have four Dell PowerConnect 6248 switches configured as a virtual chassis. One of the switches appears to have stopped working - all of the link lights are off. What's worse is, we cannot console into the switches at all. The other switches are still passing traffic. Are there any recommendations on how to regain control of our stack?
↧
Need help resetting/clearing port security on 35XX PowerConnect
I'm implementing port security on our network and I've never worked with these switches before. I'm used to the Cisco CLI which has the "clear port-sec sticky int" exec command, but there doesn't appear to be anything of the kind on the Dell CLI.
Here is the config I have in place on the switchport in question.
dot1x multiple-hosts
port security mode secure permanent
port security discard
At the moment the port has done what is is supposed to, but short of removing the config from the interface completely I am unable to find a way either in the CLI reference or online as to how to "quickly" reset the port.
Any help would be appreciated.
↧
VLAN Trunking between 6248 and 5448.
I want to connect a powerconnect 6248 to a powerconnect 5448.
I created a VLAN 5 and added the port 1 (mode access and untagged) and allow the port 46 (mode trunk and tagged) in both switches.
But the interfaces of this VLAN don't connect.
Below, I post the out of the command "show run" and "show interfaces switchport ethernet".
Dell 5448:
console# show run
interface range ethernet g(13-24)
flowcontrol on
exit
port jumbo-frame
interface ethernet g46
switchport mode trunk
exit
vlan database
vlan 5
exit
interface ethernet g1
switchport access vlan 5
exit
interface ethernet g46
switchport trunk allowed vlan add 5
exit
interface vlan 5
name ISCSI
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
interface range ethernet g(13-23)
negotiation 1000f
exit
iscsi target port 860 address 0.0.0.0
iscsi target port 3260 address 0.0.0.0
interface vlan 1
ip address 10.8.4.241 255.255.255.0
exit
interface vlan 1
ip address 192.168.52.1 255.255.255.0
exit
interface vlan 5
ip address 192.168.100.1 255.255.255.0
exit
ip default-gateway 10.8.4.13
username admin password 44f2578920365aa5536f7087f1c20241 level 15 encrypted
console# show interfaces switchport ethernet g1
Port : g1
Port Mode: Access
Gvrp Status: disabled
Ingress Filtering: true
Acceptable Frame Type: admitAll
Ingress UnTagged VLAN ( NATIVE ): 5
Protected: Disabled
Port is member in:
Vlan Name Egress rule Port Membership Type
---- -------------------------------- ----------- --------------------
5 ISCSI Untagged Static
Forbidden VLANS:
Vlan Name
---- --------------------------------
Classification rules:
Protocol based VLANs:
Group ID Vlan ID
-------- -------
console# show interfaces switchport ethernet g46
Port : g46
Port Mode: Trunk
Gvrp Status: disabled
Ingress Filtering: true
Acceptable Frame Type: admitAll
Ingress UnTagged VLAN ( NATIVE ): 1
Protected: Disabled
Port is member in:
Vlan Name Egress rule Port Membership Type
---- -------------------------------- ----------- --------------------
1 1 Untagged System
5 ISCSI Tagged Static
Forbidden VLANS:
Vlan Name
---- --------------------------------
Classification rules:
Protocol based VLANs:
Group ID Vlan ID
-------- -------
console#
Dell 6248:
console#show run
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.1.10, VxWorks 6.5"
!System Software Version 3.3.1.10
!Cut-through mode is configured as disabled
!
configure
vlan database
vlan 5
vlan routing 5 1
exit
stack
member 1 2
exit
ip address 10.1.1.1 255.255.255.0
ip routing
interface vlan 5
routing
ip address 192.168.100.2 255.255.255.0
exit
!
interface ethernet 1/g1
switchport access vlan 5
exit
!
interface ethernet 1/g46
switchport mode trunk
switchport trunk allowed vlan add 5
exit
exit
console#show interfaces switchport ethernet 1/g1
Port: 1/g1
VLAN Membership mode:Access Mode
Operating parameters:
PVID: 5
Ingress Filtering: Enabled
Acceptable Frame Type: Untagged
Default Priority: 0
GVRP status:Disabled
Protected:Disabled
Port 1/g1 is member in:
VLAN Name Egress rule Type
---- --------------------------------- ----------- --------
5 Untagged Static
Static configuration:
PVID: 5
Ingress Filtering: Enabled
Acceptable Frame Type: Untagged
Port 1/g1 is statically configured to:
VLAN Name Egress rule
---- --------------------------------- -----------
5 Untagged
Forbidden VLANS:
VLAN Name
---- ---------------------------------
console#show interfaces switchport ethernet 1/g46
Port: 1/g46
VLAN Membership mode:Trunk Mode
Operating parameters:
PVID: 1
Ingress Filtering: Enabled
Acceptable Frame Type: VLAN Only
Default Priority: 0
GVRP status:Disabled
Protected:Disabled
Port 1/g46 is member in:
VLAN Name Egress rule Type
---- --------------------------------- ----------- --------
5 Tagged Static
Static configuration:
PVID: 1
Ingress Filtering: Enabled
Acceptable Frame Type: VLAN Only
Port 1/g46 is statically configured to:
VLAN Name Egress rule
---- --------------------------------- -----------
5 Tagged
Forbidden VLANS:
VLAN Name
---- ---------------------------------
Thanks,
Breno
↧
↧
Dell Force10
Hai guys,
I'm the newbie work to dell switches force10. My client site currently have a problem of connectivity internet slowness. I ping to gateway which is core switch, dell force10, got intermittent ping reply. may i know what the possibilty it may occured ?..hope can guide me. thanks
↧
PowerConnect 2808
I'm trying to setup a powerconnect 2808 in managed mode. I pressed the managed mode button on the front and it switched over to managed mode. I connected to the default web interface at 192.168.2.1 and logged in with the default username and password. I then hit apply changes on the restore configuration page. The switch resets and I can never connect to it again. I can't ping the ip address, web interface and telnet are down. I've reset the device by holding the managed mode button for longer than 7 seconds and the switch resets. After it reboots I still can't connect to the switch. The only way I can get on the switch again is to put it back in unmanaged mode then back to managed. Then the cycle starts over again. I've tried to get into the CLI instead of the web interface and I just get the >. I type mcli and it asks for a password that I apparently don't know. I would like to get this switch setup in managed mode.
↧
Powerconnect 2848 LAG and Broadcom Link Aggregation
I 'm having trouble configuring a server with NIC Teaming via BACS4 (Broadcom) and a powerconnect 2848 (LAG). I know that the 2848 only supports static LACP and not dynamic. The three modes of NIC Teaming that BACS4 offers is:
Smart Load Balancing and Failover
802.3ad Link Aggregation using LACP
FEC/GEC Generic Trunking
What I want to accomplish is configure my server with NIC teaming using two 1GB ports and increase throughput to my server via LAG on the switch.
I've attempted configuring the switch with LAG following posts posted in this forum with no luck. Can anyone help point me in the right direction? Any help is much appreciated!
↧
Is anyone having problems with the latest firmware 3.3.6.4 for 6248?
We've been having so many problems with our 6248's ever since updating them to 3.3.6.4. Ports are blocked randomly and take hours to go back to the forwarding state. This is happening on the trunk links. I see Dell removed the 3.3.6.4 from the web.
↧
↧
Problem Connecting to Console on PowerConnect 3448
I'm using SecureCRT to connect to the switch. When i connect using the correct COM port on my desktop it appears to connect successfully but all i get is a blinking cursor. I've tried to power cycle the switch as well as reset the switch by using a paper clip to push the reset button but neither of those worked. I've tired multiple RS-232 crossover cables and verified that my terminal settings are correct (9600, 8, 1, no, none). I've also tried using different data rate numbers , but still no change
Any ideas as to what might be going on?
Thanks,
David
↧
Powerconnect 3500 POE vs the idiot cabling tech (4 wire network jacks)
I just inherited this new office setup and the client bought a 3500PoE for their phones
Right before I hook things up they tell me their new printer isn't working, I test the port and it only has 2 pairs (4 wires)!!!
Turns out they hired a cabling guy to add more ports and what he did was, instead of running more cable, he took the existing runs and split the wires ( unrelated question anyone know a lawyer? What's the punishment for castrating someone?)
Question what happens if you try to connect a phone or a computer to a PoE switch using 4 instead of 8 wires?
Will the switch turn off the port?
Will it only provide data or power?
Will it provide both but with noise due to the absence of grounding?
Will something get fried? A phone or a computer?
Thanks in advance
↧
Tagged and Untagged VLAN
We are having a Dell power connect 2748 switch. We have been facing an unusual problem. This switch is uplinked to a Cisco L3 switch which inturn caters to the WAN Connectivity.
We have multiple VLANs on the Dell and have created a trunk between the dell and the cisco switch and have tagged all the VLANs over the trunk port. We also tagged the access port for specific VLANs. What we observed that for an XP system connected to a Tagged access port, the system was able to receive an IP via DHCP whereas on the same port if we connected a Win7 PC it failed to get an IP.
To get around this we figured out to leave the access port as untagged for the specific VLAN, post which Windows 7 PC accuired IPs. But later on we found huge lags in accessing any app over the XP systems which were connected to a Tagged access port. Again we switched the access port to an untagged VLAN and everything was working smoothly.
Could anybody explain the logic of impact of an untagged / tagged frame on the overall network performance.
Thanks,
↧