how to set jumbo frame on some specific interface
Hi I m using powerconnect N4000.As i have an iscsi vlan with equalogic but not directly connected on this N4000 switch i would like to specify jumbo frame only for specific interface.but when i enter...
View ArticleNoob to vlan need help
Hello Im trying to setup a vlan on my powerconnect 2824 I would like ports 2,4 and 23 to be vlan 6, the rest of the ports can stay vlan1 with my data network.the data network works fine and is uplinked...
View ArticleDell M1000e + MI/O Aggregator port mapping
Hi All,I was planning to setup a new Dell M1000e chassis along with Dell M I/O Aggregator. During the solution time I have few queries about mapping the Physical uplink ports with Blade NDC ports. Can...
View ArticleTrunk or Channel-Group
Hello, I'm in need of some help here on what the best setup would be for my issue .I’m trying to separate the Video VLAN 41 and put on its own either Trunk or Channel-Group 41. Current...
View Article10Gb to 1Gb SFP+ Module Recommendation
Good afternoon.In error, I purchased a Dell PowerEdge R630, with a QLogic 57840S Quad Port 10Gb SFP+ Direct Attach Rack Network Daughter Card. However, the server will not be in an environment that...
View ArticleSSLVPN client Not working on PC's
Hi,I have configure a Sonicewall N3600 with SonicOS Enhanced 6.2.6.0-20n firmware, I created users and assign rights as appropriate, I configure sslvp.Whenever i try to connect to the vpn on PC with...
View ArticleForce 10 Constant rebooting
Hi all,After consoled in, the switch does nothing but repeating the following message:U-Boot 1.1.4 (F10 Development) (Oct 6 2009 - 03:14:26)Built by build at hydrogen on Tue Oct 6 3:14:25...
View Article6248 Foreign pdu on interface 84
Hello Forum,I'm struggling with the "Foreign pdu on interface 84" and 85 issue popping up in my syslogs. My first issue is, what exactly is port 84 and 85? How do I correlate this to a physical...
View ArticleSNMP OID CPU, InBroadcastPacket for Powerconnect 5324, 6248
Hi everyone,I have a problem to monitor my Powerconnect 5324 and 6248 via SNMP. I want to get informations about Broadcast Packet (per second or counter) and CPU ultilization, specially Trap Broadcast...
View ArticleS5000 - not disconnecting vty lines
Hi,our S5000 is not clearing the lines. Tried clear line x or clear line vty x, but none works. Any suggestion? Below is the OS the switch is running.Dell Operating System Version: 2.0Dell Application...
View ArticleConnect three swtich
I had bought a new switch of Dell N2028 and existing had two switch of Dell N2024Can i may below connection? Dell N2024 (SW-A) Port 1 to Dell N2024 (SW-B) Port 1 Dell N2024 (SW-A) Port 2 to Dell N2028...
View ArticleDell PowerConnect 5448 - Error traffic routing
HelloToday i sniff the traffic on my computer, and receive many traffic (http, https) of other users in our Network. We have four switches, on every switch i receive wrong traffic. For testing i remove...
View Articlebuffer-profile command on S4810P switch
Hi,I have a Dell Force10 Switch (S4810P) whose version is================================================Force10#show versionDell Force10 Real Time Operating System SoftwareDell Force10 Operating...
View ArticleStorsimple dell n3024
Hello im trying to connect a storsimple 8100 to a dell n3024 via the 10GB interface, but im getting no link on both the storsimple and on the dellOn the storsimple side we are using a SFP-10G-SR...
View ArticleDHCP over VLANs
I've been trying to implement some VLAN segmentation and network access control on our network. Our entire network currently runs on VLAN 1. We're starting with the NAC project which has a DHCP...
View ArticleN3048p - Can you stack 2 N3048p switches using the sfp+ ports on front of switch
I have 2 N3048p's. We had to add a a second closet because of distance and we have LC to LC fiber between the closets. Can I stack the 2 switches using the sfp+ fiber ports?If so, how do i go about...
View ArticleStacking PowerConnect Switches
I have one standalone PowerConnect 3548 fully loaded and in production. I am needing more ports to accommodate additional users on the VLAN 1 configured on this switch.I have with me a PowerConnect...
View ArticleClik here to view.
Memory error on Switch Dell N4032
Hi Dell team, I was looking on my Switch log register and I see for an error that i suspect that is hardware issue I made a firmware upgrade and the errors still display on logHardware issue ? Please...
View ArticlePowerconnect 3548 PXE Boot
I cannot seem to get my machines to pxe boot using an ufei bios. It will work traditionally, albeit slow but once the workstations are converted it won't pxe boot any more
View Articlem6348 lost oob connectivity
I have a m6348 two member stack in a M1000e fabric B. Has been working fine for years. Today I can no longer ping or telnet to the master. The switches are still forwarding traffic. When I look at them...
View Article