Force 10 (S4810) Class Map and Policy Map Configuration
Dear All,I am putting together a traffic policy on my Force10 switch. I want to use 3 independant class maps. The first two will match two DSCP values and place them into a specific service queue. The...
View ArticleOverlapped VLANs
Hi everyone,I'm completely new here and I'm happy to be with all of you.So I have a pc6248 and I want to make use of it. Here are what I did on the switch:Created 3 vlans: 10, 20, 30.vlan 10,20,30Set...
View Articlem6220/m1000E: How to create sub-net for each blade?
We have been assigned a class C IPv4 block. The gateway is 10.10.10.1 (example). We would like to create a /29 sub-net for each port so that the blade will have its own 5 usable IP address.How can this...
View ArticleClik here to view.
Advice on how to Create Redundant Switch Configuration
Hello,My goal is to have redundant switches for our ESXi Servers as well as redundant links from these switches back to our main Network Stack (HP). My two server switches are Dell 4032F...
View ArticleUnencrypted Telnet Server
vulnerable found on my Dellnetwork administrators IO module R1-2210 "Unencrypted Telnet Server" what is the best practice to disable telnet server.TIA.
View ArticlePowerConnect 6224 increased latency and dropping packets since IP assigned
Hi all, I have a 6224 which until recently was running quite nicely without an IP, or http access, but I don't know what configurations may have been made via console since it came out of the box. I...
View Articleduplicate multicast packet
HiI have installed new blade server with EXSI-OP on our Dell power edge 1000 chassis,in th company.the xvm that i created on the blade server gained duplicate multicast packet.unicast works fine.the...
View ArticleDell 4064F and Copper SFP (100BASE-T) - Link Status no detected
Hi,Below are all the technical details regarding the SFP in question.System Model: N4064FFirmware: 6.3.0.16Type.............................. SFPMedia............................. 1000BASE-TSerial...
View ArticleDell Power Connect 3324
I have 3 Dell Power Connect 3324 Switches that form my network which also serves has an IP phone system. I remember when I installed the switches they had to be set to give IP addresses only thru the...
View ArticleUnable to retrieve STP Port Table via SNMP on Dell N4032
On the system I'm working with, we have both Dell N4032 and Dell 2824 switches.I'm using network management software to monitor these switches via SNMP. One of the features of the software I'm using...
View ArticleRouting and VoIP on N4000 and N3000 switches
Hello,Having some issues and really could do with some answers from some smart people.Currently implementing a collapsed core network with a Dell N4032F as a core and then 22 N3024P/N3048P as edge...
View Articlen4032 encrypt local passwords?
I'm not finding a way to encrypt the user passwords for the local users on our new n4032's.I type username USER1 password PASSWORD priv 15 encrypted but the password is still plain text if I do a sh...
View ArticlePowerconnect 8024F 100Mbps copper port speed
Hello, According to the spec sheets, 100Mbps should be supported on the copper ports. However when I connect a device at 100Mbps, it just says there is no link. The lights on the front are lit, one...
View ArticleDell N4000 Stack Status - MIBs for monitoring or other hints
Hi,We use Nagios XI with the check_powerconnect plugin for monitoring our N4000 switches.This plugin provides values like general information, fan status, health, power supply status and uptime, not...
View ArticleDell N4000 spanning-tree issue
HelloWe have a setup of 2 dell N4000 switches that are stacked. We have a dual ethernet link to our office that has 4 N2000 series switches stacked.We can't use port channel or lacp on this connection...
View ArticleClik here to view.
Powerconnect M6220 Switch Unable to set port Speed
I am trying to set a port speed to 100 instead of the default 1000 using the following command:1 Enter Interface Configuration mode for port 1.console#configureconsole(config)#interface gigabitEthernet...
View ArticleConfiguration Best Practices iSCSI - x1052 switch
Hi folks, i'm looking to connect a x1052 switch to our network and configure it for iSCSI. Anyone have any current documentation on what to enable/disable on this model of switch? Thank you in advance!
View Article5548 ARP Timeout/ Switch Mode
Hi,In our production environment we are having intermittent connectivity and slowness across all subnets within our layer 2 network. Everything appears to be find from a hardware stand point....
View ArticleClik here to view.
Guest WLAN with VLAN (Dell PC 6248)
Hello Community,i want to set up a Guest WLAN using 2 VLAN's.Setup: IPFire, Dell Power Connect 6248, Netgear WNAP 320 Access PointThe Blue Interface on the Firewall tag all frames with the ID 15.On the...
View ArticleN3048P, S4810, cisco ip phones and multicast OH MY!
I am out of my realm of expertise. We are trying to get a new phone system up and running on our network and the ability to page is holding us up from going live. We have two TOR switches (S4810) that...
View Article