OMNM 5.3 what is MIB browser
hello can someone explain what the following is and what its used for in OMNM 5.3under managed resources > direct access > mib browser (PowerConnect Switch)
View ArticleLink Aggregation and VLAN Trunking
I've configured 2 switches with Link Aggregates between them. The Access ports are part of VLAN 10 but are no longer communicating via the NEWLY created LAG's. Do LAG's pass only a single VLAN or is...
View ArticleDell N2000 Series Logging Possibilities
Hi.This is a fairly simple question:The PCI-DSS requirements specifies that you have to audit all administrative commands on all network switches within the PCI scope.The old PowerConnect does not...
View Articleupdate firmware on PC8024-k blade chassis stack?
I attempted to update the firmware on a PC8024-k 2 switch stack to 5.1.5.1. After the update this is what I get:unit image1 image2 current-active next-active---- ----------- -----------...
View ArticleBest practise to realise management ports on iscsi/san switches
Hello,currently we have a management VM in our SAN, just to get to the management IPs of our SAN switches. I want to change that and remove all hosts from the SAN network.My idea was to setup a...
View ArticleConnecting PowerConnect 2824 to home modem
I have a small business I run out of the house. I want to connect my PowerConnect 2824 to the cable modem. Previously with small Netgear modems, it was just plug them in, but the 2824 doesn't...
View ArticleNEED HELP on Powerconnect 5524
Hi Guys,Need your help here . I have been assign to migrate Force10 to Powerconnect 5524 . The Force10 will be move to other place . Another end still remain with Force10 .The problem is im not...
View Articlehave two subnets on one vlan and want to assign IP of one subnet to a client...
We have Virtual desktops on a .10 subnet at our main location but our physical branches are under other subnets. how can I allow the virtual desktops to be assigned the address of branches instead? we...
View ArticleNot able to manage , management vlan via putty on access switch
We purchased 2 core N3000 and 6 N2000 switch. I set all core and access with management vlan 3 on 172.16.106.x-100. I can putty via the core and the core can ping the access server management ip. on...
View Articlen2048 / iscsi
hi there,We have a branch office that has a couple of n2048s. The intention is to use these for iSCSI (equallogic ps4000) and network traffic.One problem we have found is that you cannot set individual...
View ArticleClik here to view.
PoE stopped working on PowerConnect 7048P
Hi, Three of my switches have stopped sending Power of Ethernet to devices, the above image is the main indication that there is some type of problem, that and log entries that read:WarningSEP 10...
View Articleforce10 switch port will not switch to stack port
one port on a force10 switch will not switch to stack mode. i have run the command to remove the quad port mode and it still does network.#no stack-unit 0 port 37 portmode quadplease help.thanks .
View ArticleClik here to view.
Lag between PowerConnect 8164f and Force10
I have the attached setup but if ienable the port-channels on the Force10 switches it causes the server on the right to lose access to the 10gb storage.The stacked switches are PowerConnect 8164f and...
View ArticleWhere can I get MIBs for N2024/48, S4810, S5000
Hello,We have just upgraded our network to Dell Networking and I'm just wondering where I can get the MIBs files to enable me to create template to monitor them via ManageEngine OPManager.Appreciate if...
View ArticleNeed help configuring layer 3 between S4810 and PC6248
I'm trying to get traffic to route through an S4810 and PC6248 to allow communication between 1GB and 10GE devices.The S4810's are connected to the 10GE uplink modules in the rear of the PC6248's....
View ArticleDell PowerConnect 7048P switch query
Does it support bandwidth management like similar way in Cisco sg-300 ? I have read it have GUI access but need to know if it does help in bandwidth management like in sg-300?
View ArticleCheck bandwidth utilization
As we can check on Cisco switches the bandwidth utilization of the interface of last 5 minutes by using the command.switch#sh int po 1Port-channel1 is up, line protocol is up (connected) Hardware is...
View ArticleDell Powerconnect Access points dilemma
Good Afternoon, I installed one Dell powerconnect w-iap980 access point and three w-iap220's on the same network. Getting perfect wireless internet connect only problem is, i cant access any of the...
View ArticleMaking the switch look for startup-configuration file once it boots up.
I have a Powerconnect 7048 and Dell N4064 switch. I'm trying to figure out if there is a way to configure the switches to look for a startup-configuration file from TFTP or FTP server once they boot up...
View ArticleForce10 MXL config question
My MXL blades were configured by Dell Tech Services and are working very well, but I would like to make some config changes now and not being a network engineer I'm having trouble with the docs I've...
View Article