N3048P Switch Discards
All my new 3048P switches are showing Received and transmit DiscardsWhy am I getting these and how do I stop them?thks
View ArticleConfigure CMC (Chassis Managemenet Controller)
Hello,Now, Is the first time that I try to configure the CMC. Could you confirm me if is necessary assign IP addres through CLI or the first time is possible access CMC without IP address?On this way,...
View ArticleStencil FN2210S
Hello,I have bought 2 new modules FN2210S and I want to create a topology. I haven't still found out the stencil in "VisioCafe" website.Please, Wheres would be this stencil?Also I would be need the...
View ArticleN3048 VLAN routing and default gateway
Many thanks again for the previous help. However, I'm now trying to set this up in our 'live' network and I've run into a problem with (I think) the default gateway.Our current network uses the...
View Articlelacp enable
HiI need two ports (TenGig 0/46-47) to be a lag and enable lacp on them. When I try to enable lacp it says Error port not in default mode.Steps I have performed Enable port channel* interface...
View ArticlePowerconnect 2824 Mac Based Home Network - Periodically Network Locks Up
I have a Powerconnect 2824 home network - Frontier Cable provides source with 24 ports, including a QNAP NAS running. Periodically, the network locks up. Doesn't give me an error - just hangs loading...
View ArticleS3100 and DHCP limits
helloWhat is the maximum pool number on the S3100 serial switches and the maximum number of addresses that the dhcp server can provide.regards
View ArticleDHCP server and TFTP Server
HelloIs it possible to send with the DHCP server using the switch S serie the address of a TFTP server using the options.Regards
View ArticleThis Week's 5-Star Enterprise Support Articles
Here are this week's top-rated support articles based on accuracy, usefulness, & ease of understanding:Safety precautions to take while replacing parts in your Dell systemObtaining logs from your...
View ArticleGetting Option 156 working with Dell N3048P and Shoretel Phones
I know this is a very specific situation, but I thought maybe someone out there has the same or similar setup. We have Shoretel Phones, plugged into a Dell N3048P switch, which is plugged into a...
View ArticleDell serie S and IMC
HelloAre the switch series S compatible with the HP solution for monitoringIMC : HP Intelligent Management Center (IMC) version 5.Regards
View ArticleIntervlan routing between two N4064 switches
A question for routing between two switches. We have two IDFs, with a 4064 in each, these two switches are connected via trunk. Each switch has it's own firewall and ISP provider, and the default...
View ArticleDell PowerConnect 3548p factory reset to reset login credentials
Let me start with, I have absolutely no idea what I'm doing!I received a previously used\configured PowerConnect 3548p that I'll be setting up in a home test lab. I have my console cable attached,...
View ArticleLACP in uplink interfaces
Hello,I am trying to create a new Port-channel with ID=9 but appear the next issue:DELL(conf)#interface port-channel 9"Error: Command allowed only for uplink Lag"Thanks!
View ArticlePowerConnect 2724 - managed mode button not working
Hi, so I purchased an used dell PowerConnect 2724. I tought it is working just fine then I did one dum thing nad things got complicated. I set Admin account to a read only mode and it is the only...
View ArticleMulticasting on PowerConnect 3548p going up stream to router
I setup vlan2 on eth01. I have an esxi server attached to eth01 that hosts a vm that multicasts out to other vm's that it's hosting on itself. I'm using an out of the box network configuration on the...
View ArticleDell S4048 Switches not working with Equallogic PC 6100 series
Hi All,I replaced Cisco switch with Dell s4048 switches recently. There are 2 dell s4048 switch with stack configuration and 2 connection from each Equallogic controller to each switch. Switch ports...
View ArticleMXL 10/40GbE VLT CONFIGURATION
Hi all,We would like to implement VLT on our 2 MXL 10/40GbE switches located respectively on A1 and A2 M1000E.To do that, i will use the 40Gb QSFP+ cables and create a link aggregation between the 2...
View ArticleStacking between Two Dell4032 Switches & connection with San Storage!!
Hello,I have some doubts, kindly help me to figure it out. i just want to know how stack switches behave, like once we made them stack the standby switch will not pass any traffic? there are no need...
View ArticleUploading to a USB device on a N3024 switch
I have two different stations with the same equipment. The first station I can copy the startup-config to a USB device with no error. On the second station I always receive the file transferred failed...
View Article