Dell F10 4810 logs=IP-4-ADDRMOVE...
Hi,One of our 4810 is logging a lot of theses:%STKUNIT0-M:CP %ARPMGR-6-MAC_CHANGE: IP-4-ADDRMOVE: IP address 10.0.200.88 is moved from MAC address 7c:d1:c3:dc:e0:a1 to MAC address...
View ArticleOversized packets between N2048 and N4064F
I've set up a link between a N2048 (Tengigabitethernet 1/0/2) and a N4064F (Tengigabitethernet 1/0/48) with a DELL DAC. These two switch are configured with MTU set to 9216 on each switch.But on the 2...
View ArticleIs the Dell S3048 suitable for Storage Spaces Direct?
Storage Spaces Direct is a nice new feature in Server 2016 that lets you do fail-over and redundancy without a SAN. Traditionally your nodes would be connected to a SAN and if one node went down the...
View ArticleS4810 to N3048
Hi everyone. I'm setting up a Force10 S4810 and Dell N3048. I'm having trouble figuring out how to trunk the two together. They will be passing severval VLANs (10,12,16,20,24) so the confusion...
View ArticlePC6248 SNMP v2 not scanning.
I have eight Powerconnect 6248 switches, two stacks of three and two single switches. I use Lansweeper for my inventory and whatnot. One stack is not displaying the assets attached to the stack like...
View ArticleN4032F Management IP problems
HiAfter I get a New N4032F switch I can assign an IP and default gateway to vlanXX, then if I recover the device to redeploy it using another vlan....lets say vlan1 and try to assign it an different IP...
View ArticleDell N4032 Config emulation
Hi Everyone,I am new to Dell networking and need to hand holding to transfer a simple L3 switch config from an Avaya ERS to a Dell N4032.The config is as follows:Does anyone have any useful guidence as...
View ArticleNeed help with setting up Guess wireless LAN on Dell 6224
I currently got the Dell 6224 switch and Sonicwall NSA 3400. currently there is no VLANs setup. I need to create a seperate VLAN "2" for the guess wireless network . This is my plan:Sonicwall Internet...
View ArticleVSS and VLT
Hello,As workaround solution VSS-Cisco and VLT - Dell should live together. Someone proofed this solution and worked fine? In this way like 2x6500 works like unique only would exist one LACP configured...
View ArticleSomeone knows how to configure "switchport voice vlan" in del powerconnect 55...
Hi! I've the following configurations:vlan databasevlan 100 name data vlan 200 name voice voice vlan id 200I need to on my ip phone, run the data vlan 100 on the port "PC" and on it has the voice vlan...
View ArticleDell N2024 Colocation setup
Hi,I've been given the task of setting up a simple colocation but my knowledge of setting up managed switches is a little limited.I've been given the below IP info by a single network drop into a...
View Article6224 two-switch stack - two port-channels - MTU 900 and: one port-channel OK...
hi everyone:I found myself in situation where honestly don't know what is going on. I have 5 vlans (include management) and this one Vlan:VLAN Name Ports Type...
View ArticleS4810 firmware
HiWhere do we download the latest firmwire for Dell force10 S4810 switch?ThanksParas.
View ArticlePowerConnect 8024F: show debug messages on telnet session
Hello all,can someone give me a hint on how to enable debug messages in a telnet session on a PowerConnect 8024F switch?I configured 'logging monitor debugging' and then set 'terminal monitor' in the...
View Articlen2000 interoperability with 55xx series
helloI have 2 stacks of 55xx switches linked by fibre with the Dell N743D 10Gb/s SFP+ transceiversI need to add a third location , unfortunately the 55xx series are no longer availableI have been...
View ArticleRX Discards
I have a Dell N1524 with Code Version 6.2.6.6. I'm monitoring the Interfaces in a Software, and it is showing me RX Errors and discards in one port. In this port I have an Access Point Ruckus, but the...
View ArticlePowerconnect 8024F QinQ Configuration
Hi All, Please bare with me as this is my first post on Dell forum :)I am currently running a QinQ setup for a client as they require a L2 service from us.For all intents and purposes lets say the...
View ArticlePowerConnect 5524 Fault Tolerant Setup
We have a Hyper-V 2012 R2 Cluster with several host nodes, which are all Dell PowerEdge Servers, connected to two PowerConnect 5524 switches, in a Master/Master-Backup setup, which are in turn...
View ArticleAccidently Removed Static IP of PowerConnect 5448
I am trying to learn about network switches and need to correct something I messed up working with a Dell PowerConnect 5448. I was trying to change the static IP address of this switch and instead of...
View ArticlePlease Help!! Connecting various Dell switches..
Hi,I'm new to the group and networking as well..I've acquired the following equipment.1 Dell 8032 with 1 QSFP-R Stacking Module 5KFVW1 Dell 7048R with 2 J3PC9 10 Gbe SFP+Ethernet Module1 Mellanox...
View Article