VLAN Setup / Dell PowerConnect 2816 and 2824
I am trying to set up two VLANS on the PowerConnect 2816 (in test mode) and eventually on the 2824. Although I have read the manual carefully, I'm having a bit of a disconnect between how I associate a...
View ArticleFTOS 8.3.2.0 download?
I need an old version of FTOS.8.3.2.0Is still there anyplace online to download the .bin file??
View ArticleM1000E and PS-M4110
Hi all !I'm planning updating my management network.The following hardware is listed below:- M1000E chassis CMC MNGT- 2x M620 blades.IDRAC - 4x 10Gbe KR PTM module - PS-M4110 with 2 controllers...
View ArticleVLANs not routing
Hi,I was hoping to get VLAN 3 "Phone-VLAN" to be able to have internet access, I have a PhoneSystem on 10.10.3.1 which can ping the IP address of each VLAN and also the DHCP server 10.0.1.14 but not...
View Articles3048-on lag (link aggregation) only gets full bandwidth one way
Hello!I am struggling to get a working link aggregation here. Any help is appreciated.The environment have two servers connected to the switch (Dell s3048-on)ServerA - 10Gbps link (TenGigabitEthernet...
View Articlebest practice on connecting a stack to the rest of ...
hihoping you can share thoughts, hoping to find some advices on:how do you link up a stack (simplest, two switches) to the rest of the infrastructure which is already managed by some switches. It's...
View ArticleHelp Upgrading PowerConnect 6224
Please help, advice required on firmware updateI've been updating our powerconnect switches to the latest firmware, however one switch is proving to be problematic. We have a 6224 currently on f/w...
View ArticlePC 2824: VLAN with Trunk port
Hi everyone,I have a PowerConnect 2824 switch and try to configure a vlan-scenario but it is not working. I read a lot and it seems I've done everything right but it's still not working.Basically I...
View ArticleDell X1052 DHCP Relay Not Working
Hi,I have a problem regarding Dell X1052 that the DHCP relay is not working. Currently my DHCP server is Microsoft Server 2008 with the up of 192.168.0.20 and my switch is 10.0.247.101, i have tested...
View ArticleDell Networking N3048 with cisco switch
Hello,I have Dell Networking N3048, switch:with one access portiinterface Gi1/0/6description "Vxxxxx"switchport access vlan 12exiton other side are Cisco 2960, also with access port.Mar 22 07:10:06:...
View ArticleDell N2048, port disables when Open-Mesh A60 Access Point plugged in
I have a three N2048 stack. We purchased two Open Mesh A60 Access Points to replace some older HP APs. These Access points are PoE so we have injectors purchased through Open Mesh inline (after the...
View ArticleConfugure intervlan routing on dell powerconnect 5574
1) Added VLANS 10, 20 on the switch.2) Added IP: 10.0.10.1/24 on vlan interface 103) Added IP: 10.0.20.1/24 on vlan interface 204) Configured access vlan 10 on interface Te1/1/15) Configured access...
View ArticleN3000 - supported SFP modules?
Hi,We just bought two N3000 series switches for our server racks, together with two stacking cables.They are now installed in the racks and stacked.We are replacing two old HP switches. In one of the...
View ArticleForce10 S50-01-GE-48T-V - SFTOS-->FTOS
I am trying to convert an S50V running SFTOS 2.5.3.7 to FTOS 7.7.1.0 but receiving an error. I have tried downloading the file a couple of times.copy t10.1.1.66/.../FTOS-SB-7.7.1.0.bin image2Error...
View ArticleN3048 OOB SNMP
HiCan SNMP be configured to use the OOB port?I know on the 6000 series it was possibleI don't see that option on these switchesThksGlenn
View ArticleFCoE and iSCSI priority groups on Force10 MXL 10/40
in M1000e chassis, two Force10 MXL switches ruining in A1 and A2 slots. each of them have FC Flex I/O Module. Dell PE M620 blades installed and one EqualLogic PS4110 installed in slot 15. currently...
View ArticleSwitch X1026P: Remote management by IP
Hello,need to know how to configure a remote management by ip on the swicth X1026P.My management vlan is vlan 20 and is define as native vlan on the trunk port.I see the ip adress of the switch in my...
View ArticleDell PowerConnect 5548P VLANS for VOIP
First off, new to Dell switching and the CLI.Core Switch setup and have VLANs running fineVLAN 2 - switch management 10.6.25.xVLAN 3 - VOIP (not in use yet but DHCP setup on server) 10.6.30.xVLAN 4 -...
View Articlewhere I can find "ONIE-FTOS-SK-9.10.0.1.bin"?
Hi,I got Dell S4048-ON switch. I am student. For my research project, I need to have 10Gbps network switch. After receiving it looks like we need to install OS. I am trying to find way to install "Dell...
View Articlecan't see the port memeber in my lag in S4048-ON
HiI m trying to set up a lag i a vlt domain in two S4048-ON.I have make the following configconf tinterface tengigabitethernet 1/1port-channel-protocol lacpport-channel 1 mode activeinterface...
View Article