Setting up VLAN with Dell 3548p switch
Good morning,I am currently working on a project to provide the office I support with wireless connectivity that allows the users to also be able to access network folders and servers, as if they were...
View ArticleLAG Setup with multiple Vlans
In a LAG configuration, in order to pass vlan traffic, the port channel should be setup in Trunk or General mode while the physical ports in access mode or both should be setup in Trunk or General mode?
View ArticleDell N4032F Switch Startup
Hi there,Today ı was triying to startup 2 Dell N4032F switch.However when ı plug in the all psu cables,I realized that switch didn't start and switch green led was blinking.I would like to make sure...
View ArticleCan I connect a N3048 with a Force 10 S25 with 10Gbe?
The N3048 has already the 2 10 GbE ports in the front in use. Cant find any SFP+ expansion module to put in the back....is there any available? Can find a ethernet module, but dont think there is a...
View ArticleDell S5000 Switch Service Tag Oid
Hello, Do you know the S500 Service Tag OID ? Can't find on Dell Mibs .. Maybe don't have the right one ThanksCharles.
View ArticleDell C9010 Config Sync
Hi,I configuring two Dell C9010 Switches, and i was wondering, a way to configure the switches as one switch.the switches are in VLT, and using one RPM on each unit.my goal is to avoid configuring each...
View ArticlePowerConnect 2848 Failed boot
Good afternoon,When I turned on my switch I came across red led in the management.Can not access remotely via serial only. When I came in I came across the following...
View ArticleCan't update CPLD on member switch N2000
I'm very new to Dell switches. These particular switches were purchased and installed by an outside organization. There are 4 switches in total (N3048P, N2048P, N2024P, N2048P) and they stacked 2 of...
View Articlen4064 switch reset button?
Hi,might be a stupid question, but according to the "User’s Configuration Guide Version 6.3.0.0 and Later"there should be a reset button on the front panel, but there is none - at least nothing that...
View ArticleMultiple Vlan Trunking between Cisco and Dell switch
HI All,I am having issue with multiple vlan trunking between Cisco 3850 and Dell 7048P (code, 5.1.7.5)There is a port channel Dot1Q trunk between both two, and this trunk is only passing vlan 1...
View ArticleL3 Subinterfaces on Dell Z9100
Hi Team,While configuring the Dell Switches (Z9100, acting as a Spine switch) we need to configure the uplink ports. We are having around 6 VRFs.The site router (to which uplinks will connect) do not...
View ArticleHow to increase the https and ssh timeout on a Dell X1052 switch
Hi,We've recently acquired a couple of Dell X1052 switches and I am looking to configure the ssh timeout. I've seen other posts mention setting the exec-timeout, but there is no mention of how to set...
View ArticleLACP Passive Mode support on PowerConnect M8024-K?
Hi everyone,Please see subject, is LACP Passive Mode (is it called in Cisco "World") supported on M8024-K switches?
View ArticleProper way to shutdown N3000 stack
Hi.I have 3x Dell N3048 working as one stack.I need shutdown entire stack, what is the proper way to do that ? And of course power on them back. I should power ON one node, wait few minutes, power on...
View ArticleForce10 S50 Console issue
Hello,I have 2 Force10 S50 switches. When they were in the datacenter i was able to use the console port. However, now that they are home i want to reconfigure them for a new datacenter. The way i have...
View ArticleForce10 S50 Replacement rack ears?
Hello,I've looked on ebay and amazon, i cannot find replacement rack ears for the force10 S50 switch. Can someone tell me what i can buy to fit it?Thanks,Tom
View ArticlePowerconnect 3524P serial port disabled?
I work at an electronics recycler and we recently received a large amount of 3524P switches. Normally I end up connecting a serial cable and reset all settings to factory defaults. Here's the catch--...
View ArticleDell M IO Aggregator configuration guidance required
Hi,I am trying to configure Dell M IO Aggregator my self need some guidance. I am seeing below details when i run show running-configuration on M IO Aggregator, i was referring dell document it says...
View ArticleClik here to view.
Force10 MXL VLT with MSTP
Hello, can somebody please clarify situation with F10 MXL switches and MSTP configuration in VLT mode on them.Didn't find clear description about situation when whole network configured in MSTP and...
View ArticleRoute management VLAN that is connected to M1000e CMC through Force10 switch
I realize this involves blades and chassis configuration, but this appears to be a problem with routing through the Force10 swith so I have posted this here.We have an M1000e deployed with Force10...
View Article