X1052P and Printer Problems
Hi, i have installed an X1052P switch, basic config one vlan1 (default) static ip and uploaded the latest firmware etc.I have no devices plugged into the switch. when i up-link the switch to the...
View ArticleTrying to change Native VLAN/PVID on all ports on Powerconnect 5524P
I have a Powerconnect 5524P and I am trying to figure out how I can (from the console) change all ports to belong to PVID 50 and be tagged. Right now, PVID is 1 for all ports.I am trying to set up a...
View Articlesflow on S4048-ON
I m trying to configure sflow on my S4048-ON on all interface but when in interface modei ransflow enable interface tengigabitethernet 1/15sw-cns-coeur-ng(conf-if-te-1/15)#sflow enable% Error: Te 1/15...
View Article6248 stack not responding to pings or http
We have a stack of four 6248 switches running v3.3.3.3 firmware, which used to be pingable and I could access via http, but since one of my colleagues did some work on them a few months ago, we can do...
View ArticleCannot ping ip route gateway ip address
Hi Inter-vlan routing is working and DHCP serves to lease IP addresses correctly. ISP has configured interfaces for Internet breakout but although I can ping all vlan routed ip addresses connected I...
View ArticleMIB for n1548 switch
Hi, i am searching for MIB for n1548 switch, i could not find the exact MIB for n1548 switch. Could you please let me know exact MIB for this model.i m looking for OID to monitor memory, cpu 5 min,...
View ArticleClik here to view.
2x Dell 6024 with seperate connection + backup route => How ?
I was wondering what the best way is to create a backup route for the setup which is shown in the attachment.A backup route with a higher metric doesn't seem to work as the powerconnects don't do...
View ArticleN2048P memory stack error
Hi all,I have 3 stacked N2048P switches. For some reason i couldn't found, we started getting this errors:10.118.x.x-3 DRIVER[bcmDPC]: broad_hpc_drv.c(4428) 164658 %% Unit 0: soc_ser_correction: memory...
View ArticleN4032F Traffic Shaping and limiting
HiWe would like to be able to limit port 80 traffic on an interface also can this be done using QOS or is it an ACLthks
View ArticleForce10 MXL for non-converged use - fortygige port in switchport mode?
There's not much documentation on the various use cases of the MXL. All the docs seem to presume that this is for SAN use and that you'll be trunking to a top-of-rack switch. The MXL docs don't do a...
View ArticleStacking N4032 Switches
I currently have two N40302 switches in a stack & acting as a VLAN master with layer3 routing.I have an additional (3rd) N4032 switch in production and have also purchased a new (4th) N4032.I wish...
View ArticleDell 6224 Switch and 10Gb modules
Hello everyone,I'm looking to purchase several XFP 10Gb modules for these switches (FJ727) but I've seen these advertised as 0FJ727 and FJ727. I could not see any differences but I wanted to make...
View ArticleLosing packets between switches
Hi, I have a 6248 and a N1548P they are linked through an UTP cable, the problem is that I'm having constantly packet loss when I ping from the 6248 to the N1548P.I've already tested the cable and it...
View ArticleClik here to view.
PowerConnect M8024 is not communicating 10Gb
In I have a M1000e chassis with two M8024-K switches, and one of them came to give problems and we temporarily put an M8024 switch to replace an M8024-K that presented problems, however we are working...
View ArticleDell N4032F excessive amount of transmit discards
We started to observe excessive amount of transmit packets discard on the interfaces connecting to other switches. This two N4032F switches configured as stack and acting as distribution layer...
View ArticleDELL N1548 in redundant scenario
I'm going to setup n.4 DELL N1548 switches; they are linked throught uplink ports (10GB) as you can see in the image attached. There are n.3 servers; each server has n.2 NICs mounted using bonding mode...
View ArticleDell Enterprise Hardware & Software Updates, June 19-23
Popular DownloadsOpenManage Server Administrator (OMSA) 8.5OpenManage Essentials (OME) 2.2Support Live Image (SLI) 2.2SupportAssist Enterprise 1.0Servers & StorageDell Hybrid Cloud System for...
View ArticleM8428-K ospfv3 hello dropped
hello,ospfv3 hello packets sent out from vmware vm connected to a M8428-K switch are dropped by m8428-k - 2 vm on the same vmware host works correctly, - if I move one of the vm on a different host,...
View ArticleInherited PowerConnect 3548 prompts for password at boot.
Hi All,I have inherited a powerconnect 3548, where I work and I'm unable to get into the settings.I've entered the boot menu on startup by pressing escape, then no 3 for the password recovery option,...
View ArticleHow to block a single IP (192.168.0.1/22) on every port of switch but the...
In an educational enviroment, students add ip address 192.168.0.1 in their phone, intentionally, or by turning on hotspot, this then interferes with in-house dhcp server and gateway. We have Dell 6224-...
View Article