Trunking between PC6248 stack and PC5324
The end goal of my project is to set up guest internet on PC5324 port g1 with a WAP on vlan 172 with no access to other vlans. Other ports on the PC5324 will belong to vlan 11. As the first step I...
View ArticlePowerConnect 5548
We have a stack of three 5548 as a single logical unit. Would I reload the switch one-by-one instead of a bigband of whole stack?
View Articleusing vlan propagated by gvrp
I have configured gvrp between 2 switchs 8164F and 7048.on both gvrp is enabled and i have a trunk between two portchannel between these switcheson these port channel gvrp are enabledOn my 8164F i have...
View Article5524 - Jumbo Frames - to entire unit or only to some ports/vlan
Hi,does someone idea, if it´s possible to use Jumbo Frames only to a specific ports?After enable JumboFrames, it will create some issue to common computers network traffic?? I was planning to create a...
View ArticleCannot apply IPv4 and IPv6 ACL to same VLAN on PowerConnect 6248
I have a guest VLAN with both IPv4 and IPv6 (a normal configuration for IPv6, I assume). My 6248 lets me add IP addresses and routing for IPv4 and IPv6. It seems that no matter what I do I cannot get...
View ArticleDell powerconnect 6224 Auto Negotiation
We just installed a 6224 no stack just that one that was given to us we are a nonprofit group and we like to use 1000 full no Auto Negotiation on the ports but when i switch to disable and apply the...
View ArticleClik here to view.
Trunk from PC5448 to Cisco 3750 over FC
Hi guys,Thanks for support.I need some help for configure a trunkbetween twoPC5448and 2 groups ofCiscoSytem3750instackconfiguration.I explainmy scenario:Phisical:2 Dell PC 5448 for Server Network...
View ArticleSpanning Tree Port Discarding
Hello,I have a client with 5 PowerConnect 2800 series switches, one on each floor in a warehouse. This network runs SonicWALL wireless network which has three VLANs:1 - default10 - Corporate - has...
View ArticleProblem updating firmware on Power connect 6224 to 3.3.6.4
Hello everyone I hope someone can help me with a problem I have. I have 4 power connect 6224's and have recently wanted to apply the must current firmware of 3.3.6.4 to all 4 switches. I had no problem...
View Article5548P- inconsistent PoE experiences
I have a recently deployed stack of 3 5548P switches. I'm having some issues when trying to supply power to Ruckus 7372 wireless APs: in some ports, the APs will power on, and transit data exactly as...
View ArticleDHCP Server on Switch Force10 S4810
Please, somebody has one script with example how configure DHCP Server on Switch Force10 S50 or S4810?Regards
View ArticlePowerconnect 3424 100% cpu
I am having an issue when we plug our 3424 into another switch in that the 3424 cpu goes to 100% and stays there till a power cycle. The weird thing is that it does not affect traffic on the switch. We...
View ArticleIp default route question
Hi,I'm trying to swap out my layer 3 switch with a PowerConnect 6248P.I have 3 VLANs (1,50,60). I have all the internal routing working, but can't get any internet traffic to route out. Any advice on...
View ArticlePowerConnect 6248 - Log Errors
Hello World. I'm hoping that someone can explain this log data to me. We have two Dell PowerConnect 6248 switches stacked together. They are being used exclusivly for VMware iSCSI/Vmotion/vManage...
View ArticleDynamic Link Aggregation connecting Synology DS3612XS to Powerconnect 8132
The Synology NAS has an Intel X540-T2 NIC installed and is configured for Dynamic Link Aggregation. The NAS sees both ports on the NIC but only reports a Link Speed of 10G, instead of 20G.The...
View ArticleTrunking PowerConnect 8024 with Powerconnect 5548
I am trying to trunk the two switches. I just want to pass my two vlans which were created on both switches. if i put a port in access mode with one vlan it is fine. i can change the vlan on same port...
View ArticleInconsistent & high pings on 8164
Hello all,Just installed 5 8164's in two different stacks and seem to be getting some rather odd ping ranges. They seem to go from the 0-4ms mark with alarming regularity, but then we get balistically...
View Articlevlan
i have a sonicwall that is connected to the powerconnect 2848 switch, i created a vlan on the sonicwall on x2 that is bridged to x0, create two wireless sid one for company (ip 172.30.xx.xx) the other...
View Articlehow to bind port based acl to source ip computer instead...
Dell Powerconnect 5448. Greetings. I have an acl that works great on ports. I bind it to different ports and the acl does its job. It works based on the port that I connect the computer to. If the...
View Article6024F Multicast help
I have read every article on this forum and tried everything suggested to no avail.I have two vlans 2&3. I have a multicast encoder in vlan 2 at 10.2.0.20. I cannot get any computer in vlan 3 to...
View Article