Lost password Powerconnect 7048
Hello !Regarding our network admin has left the company, i don´t have acces to two powerconnect 7048 switches.Is there a possiblility to reset the password without loos of the configuration?Could...
View ArticleChange management vlan PC3524
Howdy, I'm new to Powerconnect switches, and between the user guide and CLI ref, I still can't figure out how to change the management vlan.Anyone have the answer?Thanks!
View ArticleClik here to view.
Need advise on managing powerconnect switches
I started out with two stacked 6248 switches in L3 mode (core). It had 3 VLANs and no ports in VLAN1. I can connect to any one of the VLAN interfaces and manage. I am not sure allowing anyone to hit...
View Articlehow to manage acl through tftp
HiWe re migration from our cisco 6505 switches to a stack of powerconnect 8164F and we have problems with the way to manage acl.In our cisco switchs we used to use the following procedures.we use to...
View ArticleProblem connecting 2 5524 switches with 10G transceivers
I have two 5524 switches connected together with FTLX8571D3BCL (A3847590) multi-mode transceivers and the packets are not arriving intact. Is this the wrong transceiver for this model or purpose. I...
View ArticleSSH, http management on 3524
I have 3524 setup and working, vlans configured and looks good. I can't ping the switch itself, and having a trunk port passing all vlans shouldn't I be able to as I would Cisco? Also http works from a...
View ArticleNew user of powerconnect 7048P Vlan and routing problems.
Hello All,I bought a powerconnect 7048P to run as my core switch with my vmware, and then be able to support my 9971 phones and wifi access points with POE. So far every thing was working fine,...
View ArticlePowerconnect 5548 Guest-Vlan and authentication issue
Hi everyone.I've got a little problem with my authentication configuration on a powerconnect 5548.I use the MAC adresses of my users to authenticate them and it works perfectly.I decided to add dynamic...
View ArticleUpdating firmware on Dell Powerconnect 6248p Stack
Hi, I need to upgrade the firmware on the switches on my stack, the stack consists of 3 Powerconnect 6248p switches all currently running firmware version 3.2.1.3. I am planning on stacking in a 4th...
View ArticleHelp needed with 6248, VLAN, new dhcp range
First of all hi to everyone.I am a bit stuck and sometimes it is best to ask for help instead of screwing up everything. I am more into vmware and AD than ip routing, vlan and switch config so sorry...
View ArticleLost ACL after reboot of switch
I have a Dell PowerConnect 5448. I created an acl using the cli. I telnet'ed into the switch and created and acl on port 19. This works well. It does its job and even after i reboot the switch (or loss...
View ArticleClik here to view.
PowerConnect 5448, How to confine DHCP BOOTREPLY message to a specific LAN port?
In order to ward off the effect of rogue DHCP server on my Ethernet network. I need to confine DHCP BOOTREPLY message to a specific LAN port on which the authorized DHCP server resides. I tried to read...
View ArticleSetting the errdisable timeout function
Does anyone know is the errdisable timeout function is set?From the STP best practices guide:BPDU Guard — PortFast moves an end-user port to forwarding state without going through all of the STP checks...
View ArticleDynamic VLAN assignment not working on 5548/8024 setup (no RADIUS requests...
Hi,We are currently tasked with implementing a dynamic VLAN assignment network infrastructure based on Dell Switch models 5548p and 8024F. In our setup we will be rolling out two 8024s, one of which...
View ArticleOMNN quick discovery problem
Hello,I recently installed the Openmanage Network ManagerProblem is that when running a quick discovery against 3 switch stacks that we have here on the network we get the following " 3 address(es) did...
View Articlepowerconnect m6220 console cable
Hi. I need to reset enable password on the switch, but i dont have a console USB-RS232 cable.Someone have pins picture of it?
View ArticlePowerconnect 6224 -Telnet and SSH configuration
I am new to programing Dell switches, have done a few older Cisco switches but never Dell switches. For some reason I can't get a telnet or ssh logins to work. Telnet I get a password to be asked for...
View ArticlePowerconnect 5548 and vlans
Good afternoon!I am looking to implement a 5548 into our existing infrastructure. I want to preface this by saying that I am very new to networking.I am looking to have at least two separate vlans.-...
View ArticleUpdating Firmware on Powerconnect 6224 Switch
I am wanting to update the firmware on my Powerconnect 6224 switch from Version 3.3.1.10 to Version 3.3.5.5. Is there any issue with this jump or will it not matter?I also would like some words of...
View ArticleClik here to view.
10 GBE uplink between 5548 and 6248 not working
We recently purchased an 10GBE SFP+ module (0U691D) for our 6248 so that we could use a 10GBE uplink with a 5548 but I have been unable to get a Link Up state between the two switches, we have...
View Article