traffic shaping on PowerConnect 28XX series
Anyone know if there are any setting to specify traffic shaping on the Dell PowerConnect 2816 or 2824 web managed switches?
View Article5448 is missing commands
When I try to configure a stactic route in the switch I get the following. I'm wondering if the image is corrupt except I have two of this model with the same trouble.aspswt1(config)# ip route x.x.x.x...
View Articlehow to check fastport setting in powerconnect 3348 /3324
hello,I am new with dell switches,I am logged into web console of powerconnect 3348 and trying to find out STP fastport setting,want to make sure that its enabled.Thanks
View ArticleDouble 802.1x radius depending on vlan
Hello alli need to build an enviroment where i should have 2 diffrents radius (Windows IAS) that checks that host have been already added to 2 differents and isolated domains)Each domain are in...
View ArticleDisabling Interface ports
Hi, We have two Dell Power Connect 6224 switches and we are trying to disable a couple of ports to prevent them being active should a network cable be plugged in. What is the best way to do this?Kind...
View ArticleSNMP Monitoring of VLANs (Some More)
I am trying to monitor traffic utilization on VLAN using SNMP. When I look at the SNMP walk, the counters for the VLANs are showing zero across the board. I've searched through the forum and found...
View ArticlePC 6248: Getting DHCP address for wrong subnet.
I recently inherited a Dell PowerConnect 6248 which I'm not that familiar with, and I'm trying to use it as a Layer3 switch.I have a VLAN 10 with an associated network of 10.10.10.0/24 and a VLAN 11...
View ArticleMultiple Locations Routing
What i know so far.3physical locations: Location1 / Location 2 / Location3ICMP is allowed over through the VPN/Firewall. I can ping other devices, from Location1, that are on the Location 2 /...
View ArticlePwerconnect 5448, Windows Server 2008 R2
Hello from France,One of my project for a customer is to create a secure authentification via 802.1X. I chose to use freeradius.But the customer didn't want to integrate a linux solution.So I switched...
View ArticlePowerConnect 6224 iSCSI Enable
I am running a SAN off of a Power Connect 6224 and was going through the setups on the Power Connect. I noticed that the iSCSI was not enabled on the switch. Can I enable the iSCSI config while...
View ArticlePowerConnect 6248 stack frozen
Hello,We have four Dell PowerConnect 6248 switches configured as a virtual chassis. One of the switches appears to have stopped working - all of the link lights are off. What's worse is, we cannot...
View ArticleNeed help resetting/clearing port security on 35XX PowerConnect
I'm implementing port security on our network and I've never worked with these switches before. I'm used to the Cisco CLI which has the "clear port-sec sticky int" exec command, but there doesn't...
View ArticleVLAN Trunking between 6248 and 5448.
I want to connect a powerconnect 6248 to a powerconnect 5448. I created a VLAN 5 and added the port 1 (mode access and untagged) and allow the port 46 (mode trunk and tagged) in both switches. But the...
View ArticleDell Force10
Hai guys,I'm the newbie work to dell switches force10. My client site currently have a problem of connectivity internet slowness. I ping to gateway which is core switch, dell force10, got intermittent...
View ArticlePowerConnect 2808
I'm trying to setup a powerconnect 2808 in managed mode. I pressed the managed mode button on the front and it switched over to managed mode. I connected to the default web interface at 192.168.2.1...
View ArticlePowerconnect 2848 LAG and Broadcom Link Aggregation
I 'm having trouble configuring a server with NIC Teaming via BACS4 (Broadcom) and a powerconnect 2848 (LAG). I know that the 2848 only supports static LACP and not dynamic. The three modes of NIC...
View ArticleIs anyone having problems with the latest firmware 3.3.6.4 for 6248?
We've been having so many problems with our 6248's ever since updating them to 3.3.6.4. Ports are blocked randomly and take hours to go back to the forwarding state. This is happening on the trunk...
View ArticleProblem Connecting to Console on PowerConnect 3448
I'm using SecureCRT to connect to the switch. When i connect using the correct COM port on my desktop it appears to connect successfully but all i get is a blinking cursor. I've tried to power cycle...
View ArticlePowerconnect 3500 POE vs the idiot cabling tech (4 wire network jacks)
I just inherited this new office setup and the client bought a 3500PoE for their phones Right before I hook things up they tell me their new printer isn't working, I test the port and it only has 2...
View ArticleTagged and Untagged VLAN
We are having a Dell power connect 2748 switch. We have been facing an unusual problem. This switch is uplinked to a Cisco L3 switch which inturn caters to the WAN Connectivity.We have multiple VLANs...
View Article