6248 - QoS IP4 Source port - range rather than single port number?
Howdy,anyone know if its possible to specify a range of ports rather than a single port number for an IP4 source port in QoS on a 6x series?Both the GUI and the CLI seem to only accept single port...
View Articlevlan communication between 2 switches 5524
HelloI am trying to setup a VLAN network between 2 switches 5524 connected with each other through the 10Gbit port:- VLAN 2 with subnet 192.168.2.1 netmask 255.255.128.0 between port 12-17- VLAN 3 with...
View Article5324's configs not honoring no negotiation/speed range config.
We updated these older switches to the newest firmware from the original factory firmware recently. 3 of the 24 ports had "no negotiation" and "speed 100" in their individual "interface ethernet"...
View ArticleDell KVM 4322DS - bricked?
I have a KVM 4322DS that I think may be bricked.It appears to have the same FW in current and alternative. Booting into either results in it sitting at the Booting line below: U-Boot version:U-Boot...
View ArticleNo response from PowerConnect 6248 after Update
hi there,after a firmwareudate from version 2.x to 3.3.5.5 my powerconnect 6248 stoped working. if i try to connect via serial connection there is no response even after power up the unit. on the...
View ArticleHyper-V VS M6220 (VLAN configuration)
Hi to all,I have a M1000e with 4 M6220 switch. 2 of 4 M6220 are dedicated to iSCSI traffic, other 2 for network. M6220 switches are not stacked.I have 6 M610 blades (1-6)A2 and B2 M6220 switches have...
View Articleconfiguration lost when master fail in a stack
i have installed two powerconnect 7048 in a stack and i lost some configuration when the master lose power.indeed i had configured https and ssh access in the master and disable telnet and http...
View ArticleCisco 4500 Link Aggregation with DELL 6248
Hi EveryoneI need to connect a Cisco 4500 in VSS mode via EtherChannel (2 x fibers) to multiple DELL 6248s.The DELL syntax looks like this:interface ethernet 1/g47channel-group 19 mode autoswitchport...
View Articlehow to configure default gateway on out-of-band mgmt 7000 series
i keep getting an message that blocks me from setting a default gateway"incorrect input" subnet conflict with either network or service port.
View ArticleLAG Configuration with 4 Powerconnect 2848 switches
Hello all,I would like to know what the best practice is for LAG port and uplink configuration between 4 Powerconnect 2848 switches? I have configured LAG between 2 switches in the past but I have not...
View ArticlePowerConnect 6224 not filtering multicast
Hello!I have a 6224 pover connect switch. Firmware version 3.3.3.3.The configuration is like this: i have 3 ports (for example 1/g2, 1/g3, 1,g4). They must be in different vlans (vlan 2, vlan 3,...
View ArticleDell PowerConnect Spanning Tree 2748
I just had a simple question about Spanning Tree. We have a network setup and everything already how hard is it to implement spanning tree on the powerconnect switches if you already have your network...
View ArticlevLan best practice
Hello,Thismight be a very simple question; I just need to be sure that what I am doing iscorrect to avoid any negative consequences.AllI need to do is add a vLan that is segregated from the default...
View ArticlePowerconnect 6224f and 6248 firmware downloads no longer listed on Dell...
Hello, I am have been looking for firmware downloads for the 6224f and 6248 powerconnect switches on the Dell support site. It looks like this series of switch is no longer listed on the Dell...
View Articlepassing multiple vlans to multiple unmanged switches question
I have a stack of dell 7024I have Vlan 1 (LAN) and Vlan 200 (DMZ)Can I configure one up-link to a dedicated DMZ switch (unmanaged) and another up-link to the dedicated LAN Switch (unmanged)?Would this...
View Articlereset the password on a Dell PowerConnect M6220
Hello, I am trying to reset the password on a Dell PowerConnect M6220. I can login to the CMC via the https webpage but dont see how to do it from there. So I am trying to plug in a USB serial cable...
View ArticleVLAN question on a powerConnect 6248
I am trying to get vlan(s) to route on a powerconnect 6248 switch. I have 5VLAN set up with routing enabled. One Vlan works great but the others do not work without changing the port configuration....
View ArticleHow to upgrade powerconnect 6224
Hi all, I have to upgrade the firmware version of 2 pwconnect 6224 in stack.I have download the firmware and read the procedure but i have a question.Is it possible to reboot the switch one after one?I...
View ArticleHelp with Dell/Force10 S60 switches and VLAN Routing
Hi,We've recently purchased 2 x Dell S60 switches to use with an Avid ISIS 5000 storage server. I'm trying to setup a VLAN for all workstations that connect to the Avid ISIS server and not having any...
View Articleopenmanage network manager does not login to switch
HiI m trying to integrate my powerconnect 8164F to onm5.1.2I can use ssh or web browser to access to the switchWhen i try to discover it through ssh i got the following messages1 Did not Respond to...
View Article