Powerconnect 7048 SNMP
Hi All,I'm using the open source software cacti to monitor traffic through my 7048 switches using snmp.Everything works fine if I monitor individual ports, but my switch is also acting as a layer 3...
View ArticlePowerConnect 5324 reset to factory default
Hi,I have a Dell PowerConnect 5324 and i need to reset it to factory settings.I am facing dificulties in connecting to the switch through Console cable, the following has been done1- tried 2 difrent...
View ArticleNewbie VLAN problem
HelloI'm a student and configure switches is something new to me. I have recently bought 2 powerconnects 6224 (not new) and updated them with the latest firmware. I would like to configure them to set...
View ArticleDell 6224 dvlan-tunnel, qinq
Good day!Dell 6224. It is necessary to send some vlan with dvlan-tunnel. For example, vlan 801, 802,803,804,1080 are created for dell 6224. How can I give them with vlan 1080?Thank you
View ArticlePowerConnect PC8024 - Unable to stack
Hello forum!I have two PC8024 10GB switches running the 5.1.2.3 firmware. I've followed multiple guides, including the Dell documentation regarding stacking the two switches and I just can't get it...
View ArticleReplace stack member. Dell 6248
Hi!We have a stack of three Dell Powerconnect 6248 switches.One of the switches has to be replaced with the newer one (same model).the well-known "pwcnt_stacking_switches.pdf" document doesn't tell how...
View ArticleDose Dell PowerConnect 8024 support backward-compatibility with 1GB NICs or...
Hello There;I have one Dell PowerConnect 8024 when I connect it to servers with 1GB nics it simply does not work. It only connect with 10GB NIcs. Can someone tell if it's backward compatible? I...
View ArticleQME 2572 FC HBA Card at Dell Poweredge M610
Hi, we have installed QConvergeConsole GUI 5.1.0.167. However the tool could not find the FC HBA card, but both Dell OpenManage, and Windows Device Manager indicate a good status of the card.After...
View ArticleHow to connect to two ISPs
Hello,I have 4 dell powerconnect 6248 in a switch stack. Multiple vlans are configured and operating correct. We are connected to internet via ASASo basically the config is:Vlan 10 192.168.10 ./24 to...
View Article5548 Stack and LACP
Hello all, First post here; so I'm sorry if I am in the wrong thread.. I inherited a bunch of 5548's.I have two 'stacks'; one stack of three(3) devices and another stack of two(2) devices.The three...
View ArticlePowerConnect 2848 MIBs
I'm hoping there's a simple directory out there that will show all the MIBs / OID options for this model switch. I was hoping to find some Search feature for this forum but can't seem to put my finger...
View ArticleClik here to view.
Aggregate links between 2 stacking 6224 and one 2848
Hello,I want to aggregate two physical Ethernet links between 2 stacking Dell PowerConnect 6224 and one 2848.Is it possible, knowing that the 2848 uses the standard 802.3ad but does not LACP support ?I...
View ArticleInterVLAN Communication
I am pretty much a novice when it comes to networking, but I think VLAN's may help with what I believe is a congested network. Here is the scenario:CAT 6 LANDell PowerEdge R70 Server 2K8 R2...
View Articledell routing question
Could someone help to convert the following routing on an existing switch stack (Nortel ERS 2 unit stack) to a newly purchased dell 6248p (2 unit stack)Here is the output from the Nortel stack.My ain...
View ArticleDisable "enable" login with TACACS
Hello,Switch Model - PowerConnect 6248PI am trying to login with TACACS.after entering username and password I was asked to put "ENABLE" password.how can i disable this request ? and only use username...
View ArticlePort Monitor issues Powerconnect 5424 Status notReady
I'm having some issues setting up a port monitor on one of the old switches that we have. My config is listed below along with what I am seeing from from the "show ports monitor" command after I have...
View Articlewhich GBIC module?
hi there,We are replacing all of our current switches in a branch office with 2x 5548 and 5x 5524sThe plan was to use some 10GB modules. (DP/N 0n743D). However it has now come to my attention that the...
View ArticlePC5524 TACACS+ & Radius
Hi Everyone I have some questions about PC5524, could anyone please kindly give me some information ? 1.Does anyony know how many Raiuds servers can be support by a PC5524 switch? 2.Can I set 2 TACACS+...
View Article8024f acl log
HiI have a "deny ip any any log" command at the end of a ACL I have applied to a interface vlan, but its not showing up on my log serverinfact I can't see any packet counters on my acl list.. also if...
View ArticleHow to create a Powerconnect 7024 ACL
I do all my switch program on Nortal/Avaya the PowerConnect 7024 is foreign to me. I have to create an ACL to block 2 IP addresses, 192.168.0.1 and 192.169.0.2.I've been reading the manual, and have an...
View Article