Powerconnect 6248 layer 2 packet trace
Hi all, We have some issues about STP protocol and i would like to know if i can traceroute packets al layer 2 level, is it possibile? Thanks, Mauro
View ArticleQuick diif serve question
Hi,I have a stack of 7048's and we run Lync phones. There is a voice vlan for the phones but, with Lync, some of the audio and video traffic will be on the workstation vlan. Lync uses DSCP marking for...
View ArticleN3048 bridge multicast
Hey there all wise folks. I'm starting to make the great migration from using the older 6248P series switches to the N3048P switches and need to do some static bridge multicast per port type stuff but...
View ArticleOME 1.3 issue displaying inventoried items
I have 8 M5424 cards that were inventoried in OME 1.3. The display only shows 3 of them, yet when I hover my mouse over the network devices, it shows the number 8. How can I fix this to display all of...
View ArticlePowerConnect 6248 and 10GB SFP Module
I recently added the 10SFP Module to the rear of a PowerConnect 6248, however it does not appear that the PowerConnect is detecting the new module. I plugged it into rear of the device under XG3 and...
View ArticleVLAN Testing
All,I have a PC 5548. I just installed a new X300 firewall router from Barracuda.The firewall also does inter-vlan routing so I setup all the subinterfaces for the vlans.I set the port on the switch...
View ArticlePowerConnect 3524P POE issue
I had a 48v Valuepoint Access point hooked into port 24 using POE with no problem. Just replaced it with a new Ubiquiti access point (24v) and when I do a show power inline, the status on port 24 is...
View ArticlePowerconnect 6248P and shoretel phones
Hello, I'm trying to get my shoretel phones to work with 6248P switch. I've configured the switch, but when the phone reboots it keeps getting the cached lease. If i change the settings on the phone...
View ArticleAny Reserved VLAN ID for 2848?
Hello,Did any Reserved VLAN ID for 2848? like CISCO Vlan 1000, 1002-1005?Thanks
View ArticleHow to make a trunk port on Dell PowerConnect 2848
Hi there!i want to know how to make a port of dell switch powerconnect 2848 as trunk.i've seen the user-guide manual, but this is not specified.There is some information regaring lag...but i don't see...
View ArticlePowerConnect 6248P not stacking with 12m cable
I am attempting to stack 2 PCT6248P via the 12m cx-4 stacking cables and it doesn't work. both start up as Master 1/7 and do not see each other, even if one is started before the other when I use the...
View ArticleDell N3048 - Jumbo Frame support per port
Hi,Can we enable Jumbo frame on a per port basis on the N3048.I remember we could do this using the PowerConnect 6224. I just need to turn on 9000+ mtu on specific ports... Thanks.
View ArticleDell 5548P
I have a Dell 3448p that is configured with our current Vlans, I have a Dell5548p that I need to connect using the same vlans that are on the 3348, I configure the 5548 with those same Vlans but now...
View ArticleBlank/Empty HyperTerminal connecting to Foundry FLS648
Has anyone run into this issue?I recently purchased a foundry FLS648 and it won't show anything on HyperTerminal, I've played with the connection settings and never got anything other than a blank...
View ArticleSetting up 'learned' MAC addresses as 'sticky ports' on DELL 7048P
Hi,Trying to setup one of our Dell 7048P switches with locked down ports based on the MAC address of the devices that are currently connected to the switch. What are the steps to do this via the GUI...
View Articlenoob initial setup on the powerstack 6248 from a 3248
hello all - we are a church with a very simple setup. we need to have one port dedicated to a public wi-fi, and the rest of the ports for the church office. one (or more) ports will connect to our...
View ArticleNew configured vlan4 could not get IP address from our AD server
Any guys can help me: Due to network expanding, I need allocate a new subnet 192.168.4.0 on our co lan. existing, 3 private LAN 192.168.1.0 (primary, connected all Windows AD server and internet...
View ArticleDell 5548P Vlans
Just connected a 5548p to our network and I can get on the web interface, I have created several vlans and set them all to access, I have one port (48) on vlan 1 as trunk, Not sure why but when I...
View ArticleClik here to view.
PC 8132 (N4032) Vlan membership access via browser - not possible
Latest firmware v6.0.1.3, two member stackNo matter what browser (tried 4 different ones so far)All I get is spinning wheel
View ArticleJust installed Solarwinds NPM - showing high receive discards PC6224 stack
Showing high receive discards with some interfaces at over 1 million discards per hour. This has probably been going on for some time but just now got visibility into the issue. The ports are for...
View Article