Remove VLAN Routing PowerConnect 6248
I'm changing the layer 3 interfaces to layer 2 and even though I have removed the IP addresses from the VLAN interfaces, the switch will not remove the "vlan routing X" statements from the config. The...
View ArticlePowerConnect 5548 ports stuck in Down*
Am hitting this problem for the second time now that ports seem to lock up and am unable to revover them by shut/no shut. Only means to recover the ports seems to be through rebooting the switch....
View ArticlePowerConnect M8024-k config question
Hello,I have a question about our PowerConnect M8024-k ISCSI config. Currently we stacked both swithes but at our next maintenance window we are going to create an LAG. But for now I want to verify...
View Articleportmode general, dot1x and not removed guest vlan
Hello,we're in the progress of rolling out 802.1X on N2000 switches. We want the following features:Fall Back to MABDynamic VLAN AssignmentGuest VLAN (for PXE)AAA per MACSo we have the following config...
View ArticleDell PowerConnect 6224
Hi,Just wondering if anyone has experienced this. We have a couple of PeR720s connected to EQL41xx units via the above 6224 (stacked). The PeR720s are part of a Hyper-V cluster (Server 20112 R2).For a...
View ArticleGetting LLDP-MED working on N3024P and N2048P for Polycom CX600 phones
I've had luck in the past with configuring LLDP-MED on 5548P's; however, the N-series switches appear to handle things quite a bit differently.Does anyone have a working configuration with these...
View Articlesslt_control.c errors. Thousands of them
sslt_control.c(577) SSLT: Exceeded maximum, ssltConnectionTaskandsslt_control.c(1037) SSLT: error on accepting the SSL connection!What do these mean?
View ArticleSyslog Support
Hello,Does the PowerConnect 2816 support syslog? The product page states it supports the RFC 3164 — BSD Syslog Protocol standard, but I can not find anywhere in the guy or the cli to configure it.TIA,Jon
View ArticleN3024F SFP can work 100MB?
Hello,I have N3024F and I can't config the SFP to work with 100MB.Is it possible or I need to change the SFP or config another thing first?ThanksSefi
View ArticleVLAN Routing Question
Good afternoon all.This may be a stupid question, hence the reason I'm not getting anywhere.I have 3 switches.1 Core and 2 connected to the main switchSo Core 6248 has a LAG Port and Physical...
View ArticleBroadCom 5720 Multi-Switch Connection failing to achieve full bandwidth
We have following Setup: 2 redundant Dell 2848 Switches, identically configured and connected via 8-Port LAG on Ports 41-48. 2 identically setup Dell R730 with BroadCom 5720. Operating System is...
View ArticleForce 10 MXL 10/40 GbE: Can a same port be tagged and untagged to different...
Dear All,I have to configure an MXL 10/40 GbE switch. In my scenario, each port 0/1-12 has to access 3 different networks.1. Management (VLAN: 10)2. Storage (VLAN: 11)3. Admin (Untagged)I can assign...
View ArticleEnable SSLv3 and TLS on PowerConnect 5448?
Is there any way to enable TLS and SSLv3 on PC5448? I have the latest firmware installed, 20046, but don't see any option to enable it. Thanks in advance.
View ArticleM6220 Configuration Assistance
Hey all,I'm trying to setup an M1000e chassis I just received. I know about nothing related to networking, but I'm good with the hardware and software components of this system. Here is my situation...
View ArticleDell R1-2401 LACP with H3C
Hi All,We try use external 4 port use LAG with LACP connect to H3C switch but some problem as below.Both side setup LACP with trunk VLAN alreadyone cable connect 0/1 port to H3C only, external client...
View Article802.3ad LAG Question on 2808 vs. 2716
Hello,Disclosure: I have a moderate amount of IT knowledge but am a newbie when it comes to networking and all the various IEEE protocols.I need a new Gigabit switch for my network to replace a 2716...
View ArticleClik here to view.
N4032 ACL Supported
Hi AllI have two N4032 switch (ver. 6.1.2.4) and they are stacking. Each of them has one 10GbE SFP+ module.I try to apply ACL on interface port 17. I apply acl8, it is working.Then I apply acl1 on port...
View ArticleHigh CPU usage on Powerconnect 8024F
Hi everyone,We have a few Powerconnect 8024F using more than 60% of its CPU time on `snoopTask`.status bytes------ ---------- free 674521408 alloc 327563488CPU Utilization: PID Name...
View ArticleMXL port configuration for PS-M4110 storage array
Dear All,I have to configure my Force10 MXL 10/40 GbE for PS-M4110 storage array. I have two PS-M4110 connected to ports 0/13 and 0/15. I have configured it in the following way.FTOS(conf)# no dcb...
View ArticleAble to view output but unable send and input on powerconnect 5424
Hi There,I'm trying to configure a PowerConnect 5424 switch to connect it within my network as one of the distribution switch. When I explain about my network; its very basic as we do not have any...
View Article