N3024 MLAG connet to EQ
Hi AllI would like to build two N3024 switch with MLAG connect to Equallogic .Only one tier. (EQ connet to N3024 directly.)Is there any official document ? Thanks.
View Article6248 accessing web admin on non management VLAN
Hi,I'm trying to set-up a 6248 as a Layer 2 switch however I'm having trouble trying to access it's web interface or even ping it's IP on a non management VLAN I've set-up.As you can see from my config...
View ArticleIs it possible to have broadcast packets forwarded to only selected ports on...
I'm considering to purchase a powerconnect 2816 switch.All nodes/ports will be on the same L3 subnet, however I need broadcast packets to be exchanged only within a selected group of ports, so that...
View Articlehow to remove stack units added by accident
Hi allI got a dell mxl switch for my that I inputed the wrong command for, now I am trying to undo it but I can't figure out how. What happened was this: I inputted this:interface range...
View ArticleOpenmanage Network Manager
hi there,I've been asked to see if I can get information about a network outage from OpenManage Network Administrator. The outage was last week and affected a whole floor of our company.I didn't...
View ArticlePowerconnect 5548 HDMI Stack Port Functionality & Limitations
Hi, I'm in the initial process of implementing new 5548s in our network and I'm considering a few different configuration options. I just want clarification on the function of the HDMI ports. Are they...
View ArticlePowerConnect 2748 Issues
We have two Dell PowerConnect switches running off of a MS 2012 R2 Server. In unmanaged mode, they both only run at 100Mbps. I've tested a couple 24 port switches we have lying around and on the same...
View ArticleNetwork Adapters
I have a Dell Inspiron 570 AMD Athlon(tm) II X2 250 Processor (2 CPUs), ~3.0GHz with Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.141211-1742)....
View ArticleDell R1-2401 - hot plug?
We currently have one of VRTX setup with the pass through module. We are going to replace the pass-through with the R1-2401 switch. My question is can we swap modules without having to power down the...
View Articlen3024F port don't work
Hello,I have n3024F switch and when I connect to the fiber port I get access and the computer get dhcp.If I plug out the fiber and connect it again I don't get access and the port became on speed 10mb...
View ArticleN3048 Jumbo frames or larger MTU
I would like to increase the MTU size, Maximum Frame size or enable Jumbo packets on my stacked N3048 switches to improve large file transfer performance, but it is not clear the best way to do this...
View Article802.1X keeps assigning vlan1
Very strange issue, I setup a test switch N2048 last week and got this working with a 2012 NPS server, Windows CA environment.I modified my config to include the correct vlans and now is it not passing...
View ArticleSonicwall TZ215
HiHAVING A CONFIGURATION ISSUE WITH A tz215 as I am new to the productI have the following configx0 -LAN 10.0.38.0X1 - WANX1 - VENDORS 172.16.4.0This is to allow us to manage the firewall from our...
View ArticleClik here to view.
Best cabling for blade M8024-k switch stack to ToR N3048 using 10GBe modules?
I have an M1000e with 2 x M8024-k switches (stacked) in B1 and B2 slots, I have connected them to the rack switches via 10gbe ports to the 2 x N3048 (Stacked) Is this the best way to connect? And how...
View ArticleVery Basic "Stacking" question
First let me say I have worked only with Cisco switches for the past 18 years! Hard to believe, but this is the first time I have been exposed to Dell switches.That said, I have a pair of PowerConnect...
View ArticleDell 6248 Public IP Issue
OverviewI'm looking to have a Dell 6248 be the Internet facing switch to the ISP. The ISP has provided me a 8.1.1.40/29 and they are using 8.1.1.41/29 as the gateway. The ISP doesn't have a VLAN but...
View ArticleLACP hashing between N3048 and CISCO SG300/SG200 + Twinax Direct Attach Cable...
Hello,In my network I've deployed two new N3048 with 2 SPF+ transceivers and SPF+ back module as core switches connected to other 3 N2048 edge switches using optical fiber and I've reused my previous...
View ArticlePowerconnect 2816 in continous reboot
HiI have a new PowerConnect 2816 Switch, when I configure the switch to managed mode if goes into a cycle continuous reboots, it happens every few minutes, the switch would come up, I can login via...
View ArticlePowerconnect 6248 Stacking Using Front SFP Ports
I am trying to stack two Dell Powerconnect 6248 switches. They are presently daisy chained together, but I have fiber modules for the front sfp ports. Theoretically I should be able to stack them. But...
View Article8132F 10gb to HP Procurve 5412zl (J8698a) w/J9309a 4port 10gbe
trying to connect 8132F 10gb (firmware: 5.0.0.4:A0) to HP Procurve 5412zl (J8698a) (firmware: K15.15.0008) w/J9309a 4port 10gbe using 15m SFP+ / SFP+ 10gbe cables to go cable.(C9999-15M-A)Link =...
View Article