8100 upgrade 5.1.0.1->6.1.2.4
I'm trying to upgrade my 8100 stack ((1) 8164 & (1) 8132) but I'm not seeing the backup image version change.I'm following the instructions included with the firmware, currently show version lists...
View ArticleDell PowerConnect 2816 Complicated VLAN Setup
Hello All,I am new on the forum but not a total n00b, however, I seem to be having some issues in understanding how to setup VLAN's....So, here is what I am trying to do.VLAN Problem Part 1I have two...
View ArticleDell 5525 Web Interface - can't assign VLAN PID
I am using the Web Interface for the 5524.I created a vlan and when I go to the Port Settings page under VLANS and click edit, the PVID field is gray and I cannot enter the new VLAN ID. All want is...
View ArticleSmall Office Network Setup Help
Hi folks,We are renting a small office in a floor which consists of many offices. The way internet is distributed here is, they have a verizon fios router and a couple of unmanaged switch, from which...
View ArticleForce10 S60 - Enabling Web GUI
Does anyone know how to access/enable the web GUI on a Force10 S60? I have the switch configured to the point that I can ping it from a client, but I cannot seem to get access from a web browser. The...
View ArticleDell 2848 and AppleTV Connection Issue
I have a Dell 2848 switch that I'm configuring. I am having trouble connecting to AppleTV boxes across the switch. If I put a computer on a port it works fine. I can ping it, it can get an ip address...
View ArticleDell powerconnect 5524 cant ping between access port and trunk port
Hi...We are setting up a new 5524 switch i have untagged access ports on vlan 20 and trunked ports where vlan 20 i allowed. I set up one computer on the access port one on the trunk port same ip...
View ArticleOID for monitoring the CPU of a Dell N2024P
Hello,Is it possible to monitor CPU load on this model?If it is, which OID would give me the information?Thanks.
View ArticleMultihome routing at 8132F
Hello,I would like to know did 8132F support multihome routing?I have enabled 'IP routing' at switch already. There are two subnet for inter routing active now.ExampleSubnet A: 111.222.333.0/24Subnet...
View ArticleHow to disable PING response at 8132F
Hello,As title, how can I disable PING response at 8132F to protect some guys to PING the switch when using it as a gateway.Thanks!
View ArticleTagging A Port on 6248
Thanks for the help in advance. I need on just one switch to have say a VLAN 20 on this one switch with native VLAN 1 separate from each other and not pass traffic back and forth. All I need is for...
View Article8024f LAG across stack members
I have 2 8024F switches in one stack. I want to use interface 1/0/21-24 and 2/0/21-24 to be part of the same port channel. Is this possible? When I try do this, I get the following error. "Row Number...
View ArticleDell 5524 - VLAN route
I have two VLANS set up on a Dell 5524 being used with vSphere 5.5.VLAN1 has access to the DMZ we are using and has the ESXi Console and a few VMs (on vSwitch 0)The static IPs being used in the VMs are...
View ArticleHow to connect to Dell7048R switch
I have this switch that I need to connect to to get an idea of its configuration. There are no 9pin ports, the switch was pulled out of production. It has a IOIOI port and another port next to it. I'm...
View ArticleEnabling LACP on a pre-existing LAG for PC5424
I have a 2-port pre-existing LAG configured between two PC5424s. LACP was never enabled. Would enabling LACP on the LAG be detrimental while there's active traffic or should it only be enabled while...
View ArticleVoice VLAN configuration on 7048P stack
We currently have a stack of 6248P switches but I have connected a stack of 7048P switches to slowly migrate users over from the older 6248P. On the 6248P we have Voice VLAN enabled and it is working...
View ArticleHow to protect UDP flood to PowerConnect
Hello,Another security question which is protect UDP flood. I have tested if UDP flood directly toward to switch (8132F). Switch CPU got much high. sflow and SNMP could not report any information...
View ArticleLink aggregation on Dell Powerconnect switches not working for PowerEdge
I'm installing a new server that has 4 gig ports and want to take advantage of port aggregation. I've configured the Broadcom software on the server to use all nics on one team.HostTeam Type 802.3...
View ArticleDell Defender Dual factor authentication disabled and Nessus Vulnerability...
Hello First time posted and I apologize if this is in the wrong section. I ve run into an issue where, when trying to scan a network with the Nessus Vulnerability scanner, I run into an issue that, the...
View ArticleN2000 sFlow and OMNM 6.0
Hi AllI have a Dell N2000 switch with firmware 6.1.2.4.I set up the sFlow destination as the OMNM server.And I enable sFlow on some interface.But I can't see any traffic flow on OMNM "traffic...
View Article