Setting flowcontrol on Force10 S25N
I have two Force10s sitting between a 3 host VMWare cluster and a EqualLogic SAN. In working with the EqualLogic support team, they suggested that best practice on our iSCSI network is to have Flow...
View ArticleM1000e Chassis + Dell MXL cards
I attended the Dell training for the Force10 Networking gear. A question came up regarding the MXL cards and I wanted to get user forum feedback. I have two MXL cards in a single MXL chassis. These...
View ArticleDell S4810 To Cisco 2800 Routers
I have two Dell S4810 switches configured in a VLT. I have two Cisco 2811 routers that have two 1GB interfaces each. I want one interface gi0/0 to connect to the Dell S4810 and the other gi0/1 to...
View ArticleHSRP configuration on PowConn 5548
Hi,I need some help to know if what I'll do make sense or not.An ISP installed 2 cisco routers with the HSRP protocol. I want to configure on the same vlan and switch, the 2 routers, a firewall and...
View ArticleMonitoring Dell force 10 switch with Microsoft SCOM
I have installed an snmp key in de switch and created an entry in scomscom displays the switch correctly but only displays memory en cpu instance I want to see the Port utilisation .Is there any...
View ArticlePC6224 Trunking/routing
I have the need to create several VLANs that will primarily be housed on this 6224, but need to be accessed over our general network. I think I have the configuration mostly complete, but I can't...
View Articlecompatible SFP
We have 8024F switches and we would like to connect them to Cisco through 10G connection.Currently we don't have Dell SFP+ module but we have Cisco SFP-10G-LR modules.Is that SFP+ modules compatible...
View ArticleIssue Restore Config To Replacement/Test Switch
I have multiple 3524P switches within my organization. We are testing backup/restore procedures and I am having issues restoring a configuration taken from one 3524P to another "test" 3524P. Note that...
View ArticleNeed to know what is the default key size when creating a crypto generate...
HiProbably I have been looking in the wrong manuals but i am looking into figuring out what is the default key size when issuing the command crypto generate command on Powerconnect...
View ArticleVlans from endpoint to gateway
Here is my problem...I Have curently 1 Vlan per location that all terminate to one 8024F per location via our Fiber. We have 4 hubs serving 28 locations and the admin office to witch all hubs trunk...
View ArticleN4032F MLAG configuration question
Hello,I have two N4032Fs running 6.2.0.5 with two MLAGs connecting to two partner switches. MLAG Po2 connects to partner A, MLAG Po4 connects to partner B. VLAN 2 is tagged on Po2 and Po4. VRRP is...
View ArticleConnecting M3048 to 2 routes, firewall and mpls - help please...
HI AllI need a bit of help with this configuration please.I have a stacked pair of m3048 switches with a default route for 5 vlans to 10.10.10.2 which goes to a firewall with a vpn back to my officeI...
View ArticleHow to password recovery step by step procedure
Hi all fri,Please help me to have Password Recovery step by step Procedure for Dell Powerconnect 3548p switch.Thanks so much.
View ArticleUplink port on PowerConnect 8024F went to state D-Down
Hello everyone,we had a strange behaviour on one of our PowerConnect 8024F switches. The uplink port of the device (connected to a 10Gig port on a Cisco Catalyst 6513) went down. The output of 'show...
View ArticleClik here to view.
Very high CPU Utilisation - PowerConnect 5548
Dear Dell Support Team,I'm searching for a solution for a high CPU utilisation on a PowerConnect 5548. (We have about 20 of this PC5548, but only one has this problem!).The switch with that symptom is...
View ArticleFinding IPs of devices configured with Static IP
Is there a way to find ip's of devices that are configured with static ip connected to powerconnect 3548 switch.Thanks
View ArticleStacking 6248 switches
What is the maximum number of 6248 switches we can stack together? Do we run into possible issue after a certain amount of switches? thanks,Leo
View ArticleDell N3048 - RADIUS Auth
Hi all,I am having some difficulty getting RADIUS authentiation working for a couple of stacks of Dell N3048 switches I have.First, some info about the environment:2 stacks of N3048's (5 switches and 6...
View Article