M6348 firmware 5.1.7.5 port get shutdown randomly
Hello,I'm not a switch expert, just basic understanding of how it works and how to setup the minimum, I had two M6348 which were previously under version 4.2.0.4, It was running fine but had some bugs...
View ArticleClik here to view.
PC6248 - 3 vlan on 1 dhcp server
Hi :)I have DHCP server on Win2012R2. where i have three scope.On PC6248 create 3 vlans (10, 20, 30) and add ip address, but when connet work stacion to any vlan's port get IP like 169.254.X.XWhere i...
View ArticleBestway to Connect One N2000 to Two 5524?
Hello All,Currently I use one N2024 with my servers and two 5524P to my workstations.What is the best way to connect N2000 with 5524.Currently both 5524 are stacked with HDMI cables and there is ONE...
View ArticleDell 6248 as main switch?
We are currently using firewall for intervlan routing and are using 6248 as access switches. But we want to migrate all the intervlan routing on 6248 and make it as the main switch for all intervlan...
View ArticlePowerConnect 2824 and 2848 LAG setup
I have one 2824 and one 2848 that are about 200yards away from each other in the same building (different suites)I have them connected on g21-g24 on the 2824 and g45-g48 on the 2848.I setup them both...
View ArticleBUG: Dell N3024 Summer Time
There's this magical place called the Southern Hemisphere, the water spins round a drain the other way and Summer happens in place of Winter! I know! How bizarre!It seems Dell doesn't seem to know of...
View ArticlePowerConnect 2708
I've got Dell PowerConnect 2708 and I can't to access the web configuration. I have tried most reset methods i've found online and in the manual, and I still can't access the default ip in managed mode...
View ArticlePowerConnect 2708 Reset
How to rest PowerConnect to factory settings?it is in managed mode and still can't access it.
View ArticleConnecting four 2824 switches with LAG guidance
Hello.I have four Powerconnect 2824 switches that I would like to link together using LAG. I am new to Dell switches and I could use some guidance. I attempted this with poor results, so any advice...
View ArticleSNMP and N3048P switch
am "close" to having successfully scanned a dell n3048p switch using SNMP.I have the snmp community setup on the switch, pointed towards my spiceworks server, and it is scanning, even shows some...
View ArticleN3048P logging
I have global logging enabled, along with switch auditing and snmp logging enabled.under severity - log file I have everything but informational and debug checked, but when i go to Log File under Logs...
View ArticleDefine Radius service type
HiWe try to configure Powerconnect switches as NAD (Network Access Devices) for Cisco ISE, ie. using Cisco ISE as Radius server. From a Wireshark capture, we can see that the Powerconnect switches...
View ArticleConfiguring VLAN Access on 2 PowerConnect 6248 Switches
We currently have a 6248 setup at our main location it has 3 6224's stacked on it with a few VLANS. We are setting up a 2nd location with a 6248 switch connected to the main switch via a fiber cable....
View ArticlePowerConnect 8132F multicast problem
Hi,I am using a PC 8132F switch and trying to test multicast. I found a strange problem. I have a device that works as the sender of multicast packets. And a server works as the receiver of multicast....
View ArticleExperience with HP switches
Does anyone have recent experience with HP enterprise class switches?The organization I work for is looking at buying new hardware and they are considering Cisco, HP and Extreme.Most of my experience...
View ArticleN4032 dropping pings after firmware upgrade to 6.2.0.5
After upgrading firmware from 6.0.1.3 to 6.2.0.5 on N4032 it is dropping ping requests. It is random but very obvious, might be every 10 to 16 reqeuest that there is no reply on.This is only for the...
View ArticlePE 5548 dropping connections
I have a setup like that:Allied Telesis x908 (10Gb GBIC) --> (10Gb GBIC port te1/0/1 ) standalone PE 5548 --> (10Gb GBIC port te1/0/2 ) --> 2 member stack PE 5548 (10Gb GBIC port te1/0/1...
View ArticleLAG Membership and port settings
When I create a LAG and add the ports, do I need to set the trunk settings on each port in the LAG or just the LAG itself or both?
View ArticleOSPF and BGP on a Dell N3024C, N3024F
I am CCNA and my background is primarily in Cisco. I have been moved into a new shop that deploys Dell for their residential/MDU internet. I am having some trouble getting OSPF to establish. First...
View ArticleQuestion about cisco 3560 series switch
Hi, all,I am looking at upgrading our wireless switches connecting to antennas from running a 100 Mbps to a gigabit connectivity. I believe that we could use WS-C3560X-24P-S . All we are interested in...
View Article