PC 6248 and Voice VLANs
Hello all,I am attempting to hook up a Cisco 7940 IP Phone to a Dell PowerConnect 6248 on Voice VLAN 200.Per a previous thread and research, I moved the management VLAN to 10 so that VLAN 1 is routable...
View ArticleVRRP stuck in initialize on Dell N4032 pair.
Two Dell N4032 switches, each with their own ISP hand off. The interface facing the ISP on each switch is Vlan 400.All user traffic behind the switches is in Vlan 500. The two switches are trunked...
View ArticleS4810 OpenFlow egress QoS
Hi, I'm implementing SDN network using Dell S4810 switches as they support OpenFlow 1.0, and it is working properly now. Also, I need to set egress QoS on the switches using OpenFlow. According to...
View ArticleNew to Dell Switches (N3048P)
I am new to Dell switches and almost all in the company I just started working for are Dell 3048 or 3024.My situation is I am the only network administrator here with several hundred employees and the...
View ArticleInherited system with LAG question
So, here is what I inherited. I have a few questions about LAG.Can't post actual configs as they are on closed network.I have one fabric (R and L) containing Dell M6220's going to 2 ports on a Cisco...
View Articleswitch lag configuratin with ewualogic and servers
could you please check this config if i miss somthing ... the 24 ports i have is 1G should i use the mtu 9216 or no need i have only tow 10G ports should i use the mtu 9216 for them also ?!System...
View ArticleHow to troubleshoot stacked s25n switches? stack-unit0 is continually in a...
I've got a stack of s25N switches running the latest software and stacked:-- Stack-unit Status -------------------------------------------------- Mgmt ID: 1 Stack-unit ID:...
View ArticleConnecting N4032 to Force10 MXL using 40G QSFP+ DA cables
Hi,I am trying to connect a N4032 switch to a Force10 MXL chassis switch using QSFP+ modules and a 40G DA cable. Now the problem I have is that when I plug the 40G QSFP DA cable in I don't get a link,...
View Article10Gbase-T module lights won't go out after switch powering up
I have a pc6248 with the latest firmware version and a 10gbase-t module whose lights do not go off after powering up the switch. But if I do a 'reload', the module lights go off and then works...
View ArticleN4032F - port-channel link state down
Hello,I have 2 N4032F stack. Today I rebooted the switchs.Now, I have an error with port-channel.The port-channel link state is down and the command:show interfaces port-channel 3Channel Ports Ch-Type...
View ArticleDell 6248 will not boot after failed firmware update.
I was trying to upgrade the firmware from 3.2.7 to 3.3.1 using tftp. The connection and loading of the image seemed to go as planned though after image verification and subsequent load attempt it...
View Article8024F Port Mirroring Not Capturing All Traffic
We have a router plugged into port Te1/0/21 that all our WAN traffic comes from into our data centre. We have port mirroring configured to mirror that port to Te1/0/22.monitor session 1 destination...
View ArticleHow to create an aggregated link
Hello,I'm trying to learn the correct way to make an aggregated link. If I was to add A1 and A2 to Trunk 1 and then tag vlans 1, 200 and untagged 100, I would do the following on a HP:Configure...
View ArticlePower-Connect 2848 Poe
does anybody know if the power connect 2848 have Poe capabilities?
View ArticleClik here to view.
How can I setup IP each port?
I have a PowerConnect 7024P switch.handling Cisco switch, I easily configured IP address in each port.As I configure "no switchport", I successfully complete inserting IP address.Taking the same...
View ArticleI/O Aggregator - Remove unused LAGs
Hi!Does anyone know how one would go about removing (old, not in use) LAGs from the DELL I/O Aggregators?I have about 5 LAGS which are not in use anymore and I want to remove them because theyare...
View ArticleLAG not working on N4032 (2 devices stacked)
Hey all,I'll give you the details of the problem (routing VLAN traffic over trunk to firewalls):I'm looking to have 5 VLANs (IDs 21-25) on the switch (Set up in Switching -> VLAN -> VLAN...
View Articlen2000 IGMP Snooping
I have a Dell n2048 switch connected to my Cisco core router. The Dell switch is layer 2 only.I have multicast traffic that should be both vlan 10 and vlan 100 (mDNS/bonjour traffic), however it only...
View ArticleDell Switch N4032F Back-up Route Capability
Hi,Is there a way that I can achieve the ff items below with N4032F.1. Back-up route: If the primary gateway goes down, it will automatically set the route to the secondary gateway defined.2.If yes,...
View ArticleDell Powerconnect 8024 to a Brocade VDX 6720
I am trying to connect a Dell 8024 to a Brocade VDX 6720 via fiber. I have the Brocade 10 Gbps SR Ethernet optical transceiver in both switches and the correct LC fiber. Both sides are configured as an...
View Article