X1052 Question
Hi all,after about 30 Minutes back and forth at the Dell hotline redirecting, I need to verify a simple question about the Switch X1052.The PDF says it has "8 MB" (sometimes written as "Mb"). Is this 8...
View ArticleDell 62xx stack, master unresponsive
Dear all,I hope you can help me find a solution to the following issue:I have a 5 unit stack with DELL 6248 and I am missing the last stack connection from unit 5 back to unit 1.Unit1 (x)()Unit2...
View ArticleiSCSI Settings disappear on N3024 after FW upgrade to 6.2.7.2 A10
Hi thereWe have an issue whereby after a firmware update to 6.2.7.2 on our Dell N3024 switches, the iSCSI optimisation settings vanish from the Web UI.After a downgrade back to 6.2.0.5, the iSCSI...
View ArticleISCSI Optimisation settings missing from Web UI after FW update to 6.2.7.2
Hi thereWe have an issue whereby after a firmware update to 6.2.7.2 on our Dell N3024 switches, the iSCSI optimisation settings vanish from the Web UI.After a downgrade back to 6.2.0.5, the iSCSI...
View ArticleEnabling STP/Root Bridge on S4048 switches
Hello,I'm looking for the correct command to enable STP (if not enabled by default) and make a S4048-ON switch the root bridge in an environment.Thanks.
View Articlephasing out Cisco help
Hi all,I'm phasing out all the old kit where I work now but I'm having a few problems with config, I think ive done whats right but Ive came in early this morning to test and it didnt go well at all.In...
View Article6 switches inter connction
Hi I have 4 dell N2024 and 2 Dell s5000 switches. i have create 2 groups and lag 2 n2024 together using ether channel same configuration in the remaining 2 switches . on other side s5000 are also LAG...
View ArticleN2000 ISDP/CDP Problem
I have over 100 N2000 switches in my network, almost all connected to Cisco 4500x switches. As of firmware 6.2.6.6, the N2000s no longer show up in a "sh cdp neigh" on the Cisco switch.Additionally,...
View Articledell powerconnect 3524p no command line
I have a dell powerconnect 3524p. I have watched it boot in the terminal screen. It goes through it's boot process, showing pass on the checks it makes. When it's done booting, it shows standalone...
View ArticleEmpty PowerConnect M8024 High CPU Usage
Hi, we have two M8024 switches in here, and they are showing high cpu utilization (constant 22% with 40% if I enable mst)Currently only one host is connected to the switch with zero activity, all other...
View ArticleSpanning Tree Topology Change Connect resets
we are having some issues with our network being extremely slow. and after running wireshark I see a lot of RST (connect resets) which I believe is bad. I ran the command show log on our DELL 6248...
View ArticleN4032 to 6224 LAG
I'm tryin to connect an N4032 to a 6224 switch via LAG. I've configured all (4) ports for Trunk type using port-channel 2 using the standard LACP settings. Will these switches simply not connect in...
View ArticlePowerConnect 6224 PIM-SM
I'm already 2 days try to resolve a trivial task. Delivery multicast content from Summit X450a to PowerConnect 6224.From the receiver vlan I see IGMP group:#show ip igmp groups interface vlan 303IP...
View ArticlePowerConnect 6248 unable to link 10Gb fiber
So I picked up a 6248 used (on a budget) and some finsar 850nm 10Gb SPF+ transievers.The switch came with 2.x.x firmware and I updated it to the latest 3.3.13.1 firmware in order to get things caught...
View ArticleConnecting 2 M6348 to a N3048P port channel/LAG issues
we have a test blade setup that we want to use separate from our production blade setup. We have some older M6348 switches in the blade and want to create lags between the switches so that there is...
View ArticleConnecting 5524 Stack with N2024 Stack
Dell Powerconnect 5524's can be stacked through HDMI and the newer N2024 models can be stacked through dell's proprietary stacking ports. Is there a way to connect these two stacks? Can you connect...
View ArticleCan you configure a local and remote SPAN on the same N2000 switch
I want to record VoIP from local ports and a remote vlan from a different N2000 switch to a destination port on the switch with the local ports mirrored on. Is this possible?When I try to add the...
View ArticleProper procedure to config two 4048S Dell switches in HA setup
Hi All,Is there any option to setup two 4048S Dell switch's in active standby mode with out using stacking,Thanks,M.N.Weerasinghe
View ArticleN3000 Access List Broken in Firmware Version 6.2.7.2?
I had a functional access list on a stack of N3048Ps at version 6.2.1.6. I upgraded the firmware to version 6.2.7.2 and the access list was not applied to a VLAN. When I attempt to apply it, I get...
View ArticleAdd TCP Port based routes on S4048-ON
I'm wondering if it is possible to create routes on an S4048-ON switch which direct traffic based on their TCP port? For example, if I was all port 80 traffic to go to 172.16.1.1 and all port 443...
View Article