Dead Circuit 2 on Dell Powerconnect 5448
Ports 13-24 (Circuit 2) on my Dell Powerconnect 5448 are dead with no lights regardless of the connection. Is there any way to have the device serviced or that circuit replaced?Thanks,Will C.
View ArticleOMNM does not deploy OS 6.2.7.2 on N2000
Wondered if anyone else is having issues deploying the latest FW for the N2000 switches using OMNM?Scheduled a few now and first one on a single switch went okay but has failed to complete on 3 stacks...
View ArticleTo stack or not to stack
Should you stack a pair of N4032s when they will be used for iSCSI? My concern would be firmware updates. Do these switches need to apply the firmware and reboot at the same time, thus interrupting iSCSI?
View Article35xx/34xx version of the "show tech-support" command.
Recently started a new position and have differing PowerConnect models I'm trying to manage, on my 6248 I was able to use the command "show tech-support" but that doesn't seem to be working on my 35xx...
View ArticleVSAN network configuration
Hello,Is there any document, guide or best practices, for configuring N4032 switches for vmware's VSAN?Thank you
View ArticleMonitoring Switch N2048 - GlobalStatus 'non-critical'
Hi there,I want to monitor my N2048 switch using centreon. To do so, I read, using SNMP, the GlobalStatus of the product (OID : .1.3.6.1.4.1.674.10895.3000.1.2.110.1). The status is 'non-critical' but...
View ArticleStack between dell force10 S4810 and S4820
Hello,I already have an infrastructure with two force10 S4810 units in stack and need to add a new unit to the stack.Since only Force10 S4820 switches are in stock, is it possible to configure a stack...
View ArticleM6220 - can't see MAC addresses
Hi everyone, first of all, sorry for my English but I belive you would understand me. I already have mounted one m6220 switch, which is perfectly fine (on A1 slot). Question is how I can add another...
View ArticleFX2 IO aggregator server-facing ports down
Dear all,I'm new to Dell community. We have just setup our FX2 chassis. The issue is as follows: -We have two FN410s IOA in the chassis.We have connected port 11 & 12 on both IOA with 10G SFP+. The...
View ArticleAll interfaces are "Detach" after reload on N4000
Hello,On two N4064, with software versions N4000v6.2.0.5a06, N4000v6.2.7.2a11 & N4000v6.2.7.4a12, I can configure via CLI and I do an update of defaults configs (after factory-defaults) by a copy...
View ArticleNewbie needs help setting up a PowerConnect 6248 - How do I connect this...
Sorry for the silly question. I am a newbie and I am stuck on the first step of setting up my PowerConnect 6248."Make sure that the switch console port is connected to a VT100 terminal or VT100...
View ArticleDell SFP+ to SFP+ 10GbE Copper Twinax Cable
Hello. Is it possible to connect PowerConnect switch M8024 -k 10GbbE with IBM storewize V5030 with 4 Dell SFP+ to SFP+ 10GbE Copper Twinax Cable 3 m in same RACK.Can there be problems with...
View ArticleDell force 10 s4820 drops connections frequently.
Hi,I have one Dell force 10 s4820t and few servers are connected to it with 10Gig cards. Model of card is Intel Corporation Ethernet Controller 10-Gigabit X540-AT2.In every approx half an hour...
View ArticleS4810P Major Alarms problems
Hello,How to clear alarms in S4810P? (clear alarms do not fix problem)#show alarms -- Minor Alarms --Alarm Type...
View ArticleSyslog Question for N Series Switches
Hello,I've set up logging to a syslog server on my N2000 series switches. One thing that I've noticed is that the originating "Host IP Address" field contains a dash and then a number within each...
View ArticleHow do I connect a N3048P to multiple Force 10 S4810 for redundancy?
OK I cannot seem to get this to work. I am trying to connect a N3048P to two S4810 switches. One I try it seems to lose connection. I have a couple n3048P stacks that I have connected to the same S4810...
View ArticleReplacement of an M8024-K stack member....
I have 3rd party support on my M1000e chassis, and I have a pair of M8024-K switches that are stacked. One has failed (DMA errors, and reboots, looping...) I'm being shipped a new switch blade....
View ArticleI cannot connect to multicast stream with N2024
I have the following scenario:One Powerconnect N2024P switch with firmware 6.2.0.5 One small router multicast that sends a multicast stream if it have a client subscribed. One VLC client.The...
View ArticleForce10 MXL - m1000e chassis - A Fabric - Arp or Mac issue - erroneous and...
We've got a new m1000e chassis manufactured in 2014 with an A and B fabric consisting of Force10 MXL, dual QSFP+ daughter card. The chassis is loaded with a new set of M630 that has Broadcom dual 10G...
View ArticleWay to automate SSH connection/commands on a series of PowerConnect Switches,...
I am attempting to figure out a way to automate commands to send out to a series of switches (around 20) showing certain configs and saving the output to a file. The way I was attempting to do this was...
View Article