G'day,
Just wondering if PowerConnect 6248p can act as a DHCP server?
I can see it can act as a rely, but having trouble seeing any doco and options relating to it being a standalone DHCP server.
Currently running firmware 3.3.5.5
Thanks in advance for the help
I understand this has been a known issue and am interested in seeing if there has been a fix or work around.
Platform is PC 6224
Version 3.2.0.9
Example:
interface vlan 452
routing
ip address 172.22.52.254 255.255.255.0
ip vrrp 52
ip vrrp 52 mode
ip vrrp 52 ip 172.22.52.1
ip vrrp 52 priority 250
ip vrrp 52 timers advertise 180
T#show ip vrrp interface vlan 452 52
Primary IP Address............................. 172.22.52.1
VMAC Address................................... 0000.5E00.0134
Authentication Type............................ None
Priority....................................... 250
Configured Priority............................ 250
Advertisement Interval (secs).................. 180
Pre-empt Mode.................................. Enable
Administrative Mode............................ Enable
State.......................................... Backup
Both L3 devices are responding to the hard addresses, but not the virtual.
I need to get Qnap 1679U-RP with Qnap 10G dual port card (Intel X520 based) to connect to stacked 2 x N4032 as port trunking 802.3ad
On the Qnap there is not much settings available :
Port Trunking & mode IEEE 802.3ad
On the switch(es) I have PO1 configured as Dynamic
console#show interfaces port-channel 1
Channel Ports Ch-Type Hash Type Min-links Local Prf
------- ----------------------------- -------- --------- --------- ---------
Po1 Active: Te1/0/19, Te2/0/19 Dynamic 7 1 Disabled
Hash Algorithm Type
1 - Source MAC, VLAN, EtherType, source module and port Id
2 - Destination MAC, VLAN, EtherType, source module and port Id
3 - Source IP and source TCP/UDP port
4 - Destination IP and destination TCP/UDP port
5 - Source/Destination MAC, VLAN, EtherType, source MODID/port
6 - Source/Destination IP and source/destination TCP/UDP port
7 - Enhanced hashing mode
But I have no connectivity at all
Seb
I'm having difficulty communicating with the SolarWinds TFTP server I just installed on my system. Our firmware for our 3324's are a decade old, and I was attempting to update the firmware using the 332448-1213.dos file that I unzipped after entering in my Service Tag on the website.
By default, the TFTP server creates a root directory in C:/TFTP-Root, which I have been attempting to use (I put the firmware in this folder) I wanted to backup the running-config prior to making any changes, so I found some Dell documentation for 3324 switches that states that by running the following commands I would be able to backup the startup-config and running-config prior to making any changes. I figured that this would also be a way to test my TFTP server as well. I telnet into the switch from my desk and the commands that I'm trying are:
console# copy startup-config tftp://192.168.2.119/startup.bak
console# copy running-config tftp://192.168.2.119/running.bak
My TFTP server shows as "started" (UDP-69), allows all IP addresses to send & receive files.
After I run either command from the CLI, I see:
.......................................................................%TFTP-N-TIMERSEND: Timeout
Copy: Undefined error
%COPY-W-TRAP: The copy operation has failed
I am able to ping my system from the CLI (My system is where the TFTP server is installed on) I'm not really sure what to do at this point. Any help would be appreciated.
Thanks in advance
Hey Everyone,
Does anyone know if I can use the 10GbE ports on the m6348 as an access port to a server and not only as a trunk/uplink? I would like to utilize this 10GbE functionality to push/pull storage volumes to an array.
Thanks!
N3024 Configuration Instructions. Anyone know where I can obtain a set of instructions on this switch?
Hi,
We're using a M100e chassis with 2 M6220 switches. The M6220 aren't connected with eachother, but are connected to 2 Cisco 2970G's:
M6220 <--> C2970G <--> C2970G <--> M6220
We're experiencing performance issues, like 1% packetloss and slow responses.
Both Cisco switche do not show any error or warning in the logs, but both powerconnects are flooded with these messages:
<189> APR 23 17:19:12 10.0.250.22-1 ISDP[122766080]: isdp_txrx.c(169) 459307 %%Foreign pdu on interface Po1
I've been searching the whole net, but haven't found an explanation of these errors.
Does anyone know where these errors come from?
Config on Powerconnects:
interface Gi1/0/17
channel-group 1 mode active
description "C2970G-a"
mtu 9216
switchport mode trunk
exit
!
interface Gi1/0/18
--More-- or (q)uit
channel-group 1 mode active
description "C2970G-a"
mtu 9216
switchport mode trunk
exit
!
interface Gi1/0/19
channel-group 1 mode active
description "C2970G-a"
mtu 9216
switchport mode trunk
exit
!
interface Gi1/0/20
channel-group 1 mode active
description "C2970G-a"
mtu 9216
switchport mode trunk
exit
!
interface port-channel 1
switchport mode trunk
mtu 9000
Config on Cisco's:
interface Port-channel2
description PCM6220-a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1001,1006-4094
switchport mode trunk
spanning-tree bpdufilter enable
!
interface GigabitEthernet0/21
description EC2-PCM6220-a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1001,1006-4094
switchport mode trunk
channel-protocol lacp
channel-group 2 mode active
!
interface GigabitEthernet0/22
description EC2-PCM6220-a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1001,1006-4094
switchport mode trunk
channel-protocol lacp
channel-group 2 mode active
!
interface GigabitEthernet0/23
description EC2-PCM6220-a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1001,1006-4094
switchport mode trunk
channel-protocol lacp
channel-group 2 mode active
!
interface GigabitEthernet0/24
description EC2-PCM6220-a
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1001,1006-4094
switchport mode trunk
channel-protocol lacp
channel-group 2 mode active
Hi
At this moment we have a flat network:
ISP <-> Sonicwall WAN (X1)
Sonicwall LAN (X0) <-> 6248 (2 Stack)
Sonicwall X1 is configured with static IP provided by ISP. X0 is connected to one of the 6248 with /24 ip series. In powerconnect, there is a VLAN 80 configured and all the ports are under VLAN 80.
Now I want to configure in a different way:
ISP <-> port 1 of 6248
port 2 <-> Sonicwall WAN
Port 3 (Need to use as a gateway IP for some servers as ISP gave us few public ip's). Want to use some ip's for PPTP server and some other servers.
port 4 Mirror of port 1 or port 2 for IDS (Want to install snort)
from port 5 to 10 I want to connect to 3 esxi hosts
11 to 48 of switch 1 for user data port and switch 2 port 1 to 40 for voip pabx.
Can anybody please help me configure this? Any suggestion is also welcome to change the above scenario to make it more functional.
Network
QUESTION
Can you route to / from vlan 1 after Management has been moved to a different vlan?
Config
!Current Configuration:
!System Description "PowerConnect 6248, 3.3.8.2, VxWorks 6.5"
!System Software Version 3.3.8.2
!Cut-through mode is configured as disabled
!
configure
vlan database
vlan 10,25,50,60,1000
vlan routing 10 1
vlan routing 50 2
vlan routing 60 3
vlan routing 25 4
vlan routing 1 5
vlan association subnet 172.16.10.0 255.255.255.0 1
vlan association subnet 172.17.10.0 255.255.255.0 10
vlan association subnet 172.17.25.0 255.255.255.0 25
vlan association subnet 172.17.50.0 255.255.255.0 50
vlan association subnet 172.17.60.0 255.255.255.0 60
exit
stack
member 1 2
exit
ip address 10.10.10.1 255.255.255.0
ip default-gateway 10.10.10.254
ip address vlan 1000
no ipv6 enable
ip routing
interface vlan 1
routing
ip address 172.16.10.17 255.255.255.0
exit
interface vlan 10
name "vlan10"
routing
ip address 172.17.10.1 255.255.255.0
exit
interface vlan 25
name "vlan25"
routing
ip address 172.17.25.1 255.255.255.0
exit
interface vlan 50
name "vlan50"
routing
ip address 172.17.50.1 255.255.255.0
exit
interface vlan 60
name "vlan60"
routing
ip address 172.17.60.1 255.255.255.0
exit
interface vlan 1000
name "Management"
exit
ip ssh server
!
interface ethernet 1/g1
switchport access vlan 1000
exit
!
interface ethernet 1/g9
switchport mode general
exit
!
interface ethernet 1/g35
switchport mode general
switchport general allowed vlan add 25,50,60 tagged
switchport general allowed vlan add 1 tagged
exit
Hi Everybody:
Im conecting a phisical trunk, between switch Dell PowerConnect 5324 and Cisco 2811 Router, please see the attachment topology, I can't not ping between the PC A and PC B, I will show the configs:
The config in the router CISCO:
!
interface FastEthernet0/0
description Cisco to Trunk DELL
no ip address
duplex auto
speed auto
!
!
interface FastEthernet0/0.2
description VLAN 2
encapsulation dot1Q 2 native
ip address 200.71.155.193 255.255.255.248
!
interface FastEthernet0/0.3
description VLAN 3
encapsulation dot1Q 3
ip address 201.249.204.153 255.255.255.248
!
Config DELL POWERCONNECT:
Configuring VLAN Trunk in Ethernet G23 :
interface ethernet g23
switchport mode trunk
switchport trunk allowed vlan add 2,3
exit
ADDING VLAN 2 AND 3:
enable
configure
vlan database
vlan 2
vlan 3
exit
Configuring Ports E2 , E3 in VLANS 2, 3 respectivily:
interface ethernet e2
switchport mode access
switchport access vlan 2
exit
interface ethernet e3
switchport mode access
switchport access vlan 3
exit
copy running-config startup-config
Could you tell me what is missing on my config? Thanks in advance.
Hello,
I've never setup a switch before so I'm in search of some assistance and guides that may assist me.
Basically I need to route our IPs through the switch and also have a specific range of IPs for a specific range of ports in a vlan. For instance, I have vlan 2 which would have port 1-10 and assign an IP range to that vlan i.e. 67.xxx.xxx.160 /28.
The switch is hosted within a datacenter.
If anyone can provide me with some assistance or any known guides on how to configure this I'd be greatly appreciative.
Thanks.
hi,
my 10g module on 6248 switch is unable to pass tcp traffic (ssh,http, etc) from untagged access port if uplink is trunked from a different vendor switch. ICMP, UDP, works fine,
please help.
Regards,
Gene
I recently purchased switches to run data and phones for our office, however I'm having some issues with the SFP+ adapters not linking.
The transceivers in question are Intel branded "FTLX8571D3BCV-IT" (Intel Prod Code E10GSFPSR). I also have a few Dell "FTLX8571D3BCL" SFP's that seem to work fine.
I also have other Intel 10GbE SFP+ transceivers "AFBR-703SDZ-IN2" (also Intel Prod Code E10SFPSR) that work just fine.
The 5548P will log when the non-working SFPs are plugged in and unplugged. If I run "show fiber-ports optical-transceivers", I am able to see vital stats from the "non-working" ports, including stating that there is no loss of signal on the port. I can also watch the Input Power field and am able to tell when a fiber is connected or not. All of this is also true when the same SFPs are connected to an 8132F. Both switches are running the latest firmware available (8132F - v5.1.1.7; 5548P - 4.1.0.10).
Any ideas on what could possibly be causing these transceivers to not link and function properly?
Hello,
Is the switch 6224P support QinQ mode?
If yes, can you give me the configuration please?
Version: 3.2
Sys Object ID: .3.6.1.4.1.674.10895.3010
Serial No. : CN0MY2872829874S0029
Regards,
hi guys, i've download the datasheet of this product, but i don't find how RAM memory this switch has, and how Flash memory also>
THe same thing, happens with other switches also 5524, 6224 etc...
Let me know, as we have to bid on a tender where is required that switch must have:
minimumi32MB DRAM or incorporated SDRAM
minimumi 16MB flash memory incoporated
Regards!
We are trying to purchase seven n2000 series. Our objective is to try to stack this together. However my question is when you stack, all 7 switches will be as one. if i were to split this 7 switch to different vlan, how would Layer 3 Core knows when I already configure the port. For example , port 1 for internet, port 2 for vlan 50 (r&d), port 4 (Accounting), etcs etcs... if the seven access layers stacked switch, how would configure to split those switch and connected to the core?
Hi all, I'm a little new to networking switches but was given a PowerConnect 5448 and I'm having trouble accessing the Web GUI. Here's what I did so far:
I realize the switch doesn't have DHCP so I can't directly plug my laptop into it. So, I plugged the switch into a spare router which my laptop was plugged into. I ran an iplookup hoping to find the PowerConnect IP address to log into, but it wasn't showing up at all. This is where I wasn't sure what to do next...
Should I find a serial cable and access it that way or do some kind of hard reset? Any advice would be appreciated! Thanks :)
I want to have multicast working on 2 ports in my switch. How can I do this? It worked until I changed my ports to General to add a tagged vlan to it. From then on my multicast has stopped working.
Attached is my config. g1 and g3 are the ports I want multicast working. What else to I need to add to get it working?
Mark
Hi, I have four PC7048s in my DMZ. External facing, Internal facing and 2 separate DMZs. All good. All working.
Since they are DMZs i only want them to route between each other and so have switched off SSH, Https, Telnet and http management so they cannot be remotely managed from those DMZ subnets.
I then plugged the OOB interfaces into my internal management switch and VLAN them accordingly. Great i can now ping my OOB interfaces on all four. But i cannot manage them since i have disabled SSH, HTTPS, HTTP and Telnet
If i enable them (just SSH and HTTPS) i am now able to manage the switches from the DMZ subnet on the DMZ IPs
I thought the point of the OOB was so this didn't happen and there was isolation? If i have to globally switch on HTTPS and SSH then they're not really properly isolated (i understand that traffic from OOB cannot talk to IN-Band etc - it's the fact that i have to turn on a global configuration for in isolated OOB service)
Am i missing something?
Thanks