MSTP / rapid-pvst instances
HiHow many spanning tree instances (MST or rapid-pvst) are supported by N-series switches?I can't find this information in technical specification,Thanks for answeringMKSH
View ArticleN4032 configuration issues/doubts
Hi Community,I'm seeking guidance on a few doubts about the N4032 configuration issues. Although I have taken networking classes with Cisco switches still new to the field, never configured N4032...
View ArticleSettings Jumbo frame on N4064F with mixed port settings
Hello All,I am in process of configuring N4064F switch that will act as Xenservers hyper-visors backbone We intend to connect 2x10G LACP for each server, 8 of them to use nfs storage mount connection...
View ArticleEnable SSH on Dell Power connect 2848
I have a dell power connect 2848 and I am looking to enable ssh on it. I have tried following the below instructions but they all error out for me except the config command but i can still make no...
View ArticleBuy High Quality Real/Fakepassports(mazzini865docs@gmail.com),USA GREEN CARDS...
Buy High Quality Real/Fakepassports(mazzini865docs@gmail.com),USA GREEN CARDS etc Apply for your passport,citizenship,Id cards,driver’s license,diplomas,degrees,certificates service available. And...
View ArticlePowerEdge VRTX R1-2401 Configuration
So I am trying to setup the installed 2401 switch in the chassis and I am running into my first issue right out of the gate. Error message: Duplicated IP interface on the same subnet.Situation: I have...
View ArticlePowerConnect 5424 MAC based VLAN assignment
I have a pair of Powerconnect 5424 switches that have been in service for quite some time for our EqualLogic arrays. We are now adding a Compellent SC4020 to the mix, and due to the PowerConnects not...
View ArticleClik here to view.
2 FN410T in FX2 in VLT-Mode
Hello,we have a FX2 with 2 FN410T as IOMs. I changed the mode from Standalone to VLT and I'm not sure if this works correctly. I did it strongly like advised in the Deployment-Guide found here:But the...
View ArticleClik here to view.
What is the best practice N4064F for setting lacp lagg Hash Configuration...
Hello,I need to set port channel lacp lagg for use with nfs protocol , the switch type is N4064FUnder LAG Hash Configuration there are several option as shown in attached image , My question is what...
View ArticleNot able to ping default gateway from blade server
Dear All,I'm facing connectivity issue with M630 blade server. I m not able to ping default gateway from blade server. We have MXL 10/40Gbe Switch IO Module on back panel of M1000e chassis.We have...
View Articlestep by step switch setup for 10 times Dell X1018P to be used for cctv
Hi can anyone please provide me with a step by step process of how to setup the Dell X1018Pi have 10 of these switches that need to be connected all with daisy chain topology. (Cat 6 cable)Also...
View ArticleConfiguring RSPAN span/mirror port to see all vlan traffic in Dell N3048P...
Hi everyone,I am working on installing a trial Websense/Forcepoint installed in Hyper-V Windows 2012R R2. I am not able to get the server to see other VLAN LAN segment traffic. At this point I have...
View ArticleDell X1052P Switches & Dell TZ300
I have a dell TZ600 sonicwall and 4 Dell x1052P switches in different NOC rooms. 2 in NOC-A, 1 in NOC-B and another in NOC-C. The two in NOC-A are connected by 10GBe connection and the others are 2 X...
View ArticleDell X1052P Firmware Upgrade - Console Putty Issue
I want to upgrade the firmware on the x1052P switches and read it needs to be done in CLI. However whenever I connect the cable and use PUTTY - PUTTY just dings and I click Open.Using a windows 7...
View Article5548 Remove Switch from Stack
I have a 3 switch stack of 5548's. My needs have changed and no long need the third switch in the stack, so I wanted to remove it. I removed spanning-tree on all the ports on switch 3. Then I moved...
View ArticleLink Aggregation LAG
Hi, I'm starting on dell switching and I wonder if it is posible to create a link aggregation between a dell switch N3000 and a cisco switch core 4506E, thanks for your time.
View ArticleN3024F fibre connection to N3024 uplink not working
Hello,I have installed an N3024F switch which acts as a distribution switch to the Up-link of N3024 switches on different floors. The switches on other floors are N3024 24 port Ethernet.When I plug in...
View ArticleConigurar Rota entre duas vlans para comunicção de duas empresas usando...
Bom dia, estou com uma questão a resolver na minha empresa.Possuimos um switch 3com configurado com duas Vlans, um com a rede interna 192.168.0.0 255.255.0.0 e a outra vlan 172.23.24.0 255.255.248.0O...
View Articlelacp on multiple switches
+------------------+ first cable | switch core 1 |------------+------------------+ + + single +-------------+...
View ArticleDell 6224 Fan Air Flow
Hello everyone,I decided to replace the fans on my 6224 so that I could use that switch near my desk. After some hit and miss I have fans that work with this but in the time delay from when I started...
View Article