Power Connect 6224 VLAN routing and management VLAN
Happy holidays everyone - I've been reading through several posts here and elsewhere about the 6224's inability to route its own management interface. Ok, enough, I get it. But what I don't get is a...
View ArticleOID for CPU load - PowerConnect switch 5424 and 5524
Hello, I need OID for CPU load of PowerConnect switch 5424 and 5524 to configure CPU load in Nagios System. Please help me on the same. Thanks,Imran Khan.
View ArticleN30xx in band access
I have two N30xx switches at two different locations running as layer 3 switches. Both are performing well as routing switch running static and ospf.. However, I cannot access the switches such as...
View ArticleProblem: Packet loss R1-2401 switch installed in the Dell VRTX
Was purchased 2 Dell VRTX with the same equipment - (R1-2401, 2xM620). VRTX first went into production immediately after unpacking: installed ESXi 5.5. Update2...
View ArticlePowerConnect 28xx - new vlan will not pass traffic...
Greetings -- I'm a new owner of a PowerConnect 2824. I'm trying to configure two VLANs, one for the 'clean' side of my network (VLAN 1) and one for the dirty side of my network (outside the...
View Article62xx series VLANs and STP
Hi, starting from a factory-reset configuration and adding a couple of vlans, and enabling routing between them, it looks like the switch is allowing STP traffic to cross the vlan boundaries. This is...
View ArticlePC 6224 hybrid port settings
Hello everyone, I'm trying to configure one of the ports of a relatively old 6224 to accept both tagged and untagged packets. Ideally a Linux workstation should be configured with a default IP address...
View ArticleDell PowerConnect 6248 and 8024F
Hi,I currently have a network with 7 Powerconnect 6248 with 10G fibre uplinks to a Powerconnect 8024F.I need to do firmware upgrades on the 6248 and 8024F. The 8024 switch is currently on version...
View ArticleHow to get port description over SNMP on PowerConnect 5548
Hi All,I am using PowerConnect 5548 firmware 4.1.0.8I want to get a port description configured over SNMP.Ex:SW conf:interface gigabitethernet1/0/1description testtest spanning-tree portfast...
View ArticleLAG connection for Server on paired 5448's
Good Day PowerConnect fansI currently have a Dell 2950 with a dual port BCM5708 and dual port BCM5709 NICs. I want to use the BACS 4 LACP teaming option toi connect these ports over two 5448's that are...
View ArticlePowerconnect 7048 Redundancy Problems
Hello! I recently set up a network that I am having trouble with and need someone to scan through my switch configs and tell me if they see anything that I have done wrong.The network consists of an...
View ArticleNetworking Issues
Hi,I am working as Networking engineer at Aschere Energy Dallas.I have configured a switch through the network, But it is showing networking error while accessing on the PC.Please suggest to get rid...
View ArticleConnecting Two Switches 7024 and 6248 with VLANs
Hello,So we have a (7024) switch that has a connection from one of our routers carrying a network and all others ports are access ports and sit on VLAN1 and connect to some hosts. I have added a second...
View ArticlePowerConnect 5548P
under switching, vlan, and port settings if I click on edit I get a blank screen. Turns out it was the compatibility setting in IE. Just thought I would mention it if anyone was having the same problem.
View ArticlePossible to stack 4 7048 Switches 2 on each floor
How would you stack a total of 4 7048 switches with 2 switches on each floor? Both groups of 2 switches are located 1 floor apart from each other. What additional modules and cables are required?thanks.
View ArticleInterVLAN of 8132F L3 to L2 switch and transfer to default next hop
Hello,I am now designing inter Vlan routing where Dell 8132F as a default gateway for internal which will connecting to others L2 switch.8132F will hold multi secondary IP like following.I have a...
View ArticleInterVLAN of 8132F L3 to L2 switch and transfer to default next hop
I am now designing inter Vlan routing where Dell 8132F as a default gateway for internal which will connecting to others L2 switch.8132F will hold multi secondary IP like following.I have a question...
View ArticleDell PC3448P / Sonicwall NSA220
Posted this over at Spiceworks as well.Looking for suggestions on how to setup the following between a Dell PowerConnect 3448P switch and a Sonicwall NSA220.We are switching over to a hosted phone...
View ArticlePowerConnect 8024F lacks vlan routing
My department recently purchased a PC8024F (F/W 5.1.2.3) which will need VLAN routing. From what I can tell the 8024F is suppose to have VLAN routing but this one is without.Is there something I am...
View ArticlePowerconnect 6200
I'm having the hardest time getting a 6248 switch to work with vlans. I originally hooked up two 5448's and got vlan2 going nicely between them. I stuck the 6248 in between the two 5400's thinking...
View Article