Intervlan routing for S4810 VLT
HiI Just want to clarify things because I confuse about intervlan routing if it is possible to implement if I used VLT's First when I configured VLT domain in my two core switches(S4810), I need to...
View ArticleDell PowerConnect 2824 VLAN Setup
I have been trying to set up and configure our older Dell PC 2824. I'd like to configure a VLAN on the switch but I am having a hard time getting internet access on the ports that are part of the...
View Articlesegregate computers from each other
I've got 15 computers plugged into my switch all using the same internet connection, also plugged into the switch. The cable modem provides the DHCP addresses for the 15 computers. I'd like to...
View Article8132F Out of Band default gateway
Hello,I want to check is it 8132F out-of-band default gateway is same as switch's default gateway.As I am now 8132F default gateway is not same as out-of-band default gateway.---interface out-of-bandip...
View ArticleSTATSMGR error - Failure in function collectorGet
I have started getting STATSMGR errors filling the log files to the exclusion of any others on the core stack of PowerConnect 7048s. The current firmware is 4.1.0.6 and I am reluctant to upgrade the...
View ArticleIP DHCP Snooping on a Dell N series switch
My DHCP server is a BSD box that bridges all user VLANs and listens for DHCP requests that way and responds accordingly. We have users on one specific VLAN who are getting bad IPs from a rogue DHCP...
View ArticleAdditional static route problem for 8132F
Hello,I have a problem when adding static route into 8132f for allow OOB to access from another subnet When I added to following static in in below and it got a error message.---console(config)#ip...
View ArticleBPDU after dot1x authentication
Hello, I have recently noticed a possible bug on DELL Powerconnect 6248 (fw: 3.3.9.1)I run MST with 1 instance and bpdu-filter disabled. I noticed that when a port is enabled via dot1x mac-based...
View Articlepc6224 vlans & routing
dear everybodyI have a default vlan1 with management interface and a port based vlan2 with "switchport mode access", have given vlan2 an IP and routing then "ip routing" as per docs.I must be missing...
View ArticleConnecting 2 N3048P switches for HA to 2 S4810 Switches.
We have a new office where we were fortunate to be able to start from the ground up. Our layout is that we have 2 S4810 Switches which are our top of rack switches (TOR), We then have our end user...
View ArticlePower Connect 6200 series Port-channel group not working
Hello , I'm in search of some much needed HELP here. I recently added a few more Ports to our port channel group(s) and changed port #'s . The issue I'm having is that my DHCP is not...
View ArticleVLT backup link needs to have a physical connection?
Hi allCan I ask a question I just finished configuring my core switch with VLT Domain but my heartbeat status is disabled, I already configured backup destination for both vlt peer 1 and 2 I just want...
View ArticleFX2 management IP's for IOA A1 & A2 switching from CMC mgmt ports to IOA 10Gb...
FX2 management IP's for IOA A1 & A2 switching from CMC mgmt ports to IOA 10Gb portsHi I'm hoping someone in either the PowerConnect or PowerEdge forums can help us with this so I'm posting in both....
View ArticleDell force10 MXL cannot access Web GUI
Hi Dell TeamI just want to ask i have a problem on my dell force10 mxl, I failed to access my web gui eventhough I already upgrade my firmware version to 9.6 and I also installed smartscript in my ftos...
View ArticleWhat needs more bandwidth, The MLAG connections of the switch interconnects?
Have a slight quandary and wanted to know what needs the higher bandwidth.Set up is that we have 2 S4810 using VLT. We have 2 N3000 series switches in an MLAG. The problem is that the N series is a...
View ArticleIssue with Basic VLAN's
Hi there;I might be doing this completely wrong, but I can't seem to find an answer. I am just trying to do basic LAGs between multiple N2048P switches and trunk multiple VLANs between them up to our...
View ArticleHelped configuring Wireless Access Point: - W-IAP215 and Open Manage Network...
Hi AllI just want to ask about this Access Points what configuration do I need to do here also what is the range of the connectivity of this AP I preferred to have two access point per floor and it...
View ArticlePowerConnect M6348 Case ID 875892
We updated our Dell PowerConnect M6348 with firmware version 5.1.8.2,A32 because we saw in the Fixes & Enhancements notes Case ID 875892 SSL/SSH Vulnerabilities listed. What is fixed in case...
View ArticleClik here to view.
PowerConnect 54XX - SNMP setting via web browser
Hello all,I have got some older switches DELL 5424 to use them in our testfield. I wanted to enable SNMP, but I could not set "Community" and "ADD", because window frame is always corrupted. No matter...
View ArticleDell PowerConnect 6248 multiple monitoring sessions?
Hello All,I have a Dell PowerConnect and I need to set up two port mirrors. It looks like I just need to add a port mirroring session, but I cannot figure out how to do that. I have read the...
View Article