Dell PowerConnect 6248 10 GB ports not working
Hello,We recently installed a SFP+ module (part # c107d) in to our Dell PowerConnect 6248 switch. The switch does not appear to be seeing the module because prior to us installing the module it showed...
View ArticleDell 8024-k chassis switches appearing as 16+4 port 10GbE switches when they...
** I answered my own question. It seems there are 16 internal nics on the 8024-k and there are NDC (network daughter cards) on the blade servers that work internally to get use those 32 'nics'. Then...
View ArticleN3024 - Can switch handle duplicate IPs in private-isolated vlan community?
I'm trying to get multiple hosts will the same IP address to synchronize to a single NTP time server (single IP). I created a primary vlan with an isolated secondary vlan so the hosts cannot see each...
View ArticleS25N does not boot
I work for a non-profit and a local company donated a S25N switch to us, but it does not boot. The following is the boot sequence, which seems normal up to around line 41. I tried pressing various keys...
View ArticleQSFP+ LM4 Optic LC compatibility with S4810 and MXL10/40
HiThere is a relatively new QSFP+ Optic Module with integrated WDM funtionality to transport 40G over a single pair of OM4 multi mode fiber with LC connector.407-BBRC Dell Networking, Transceiver,...
View ArticlePowerConnect 5548 stack - one switch not working
I have a stack of 5 5548 switches using HDMI cables with a cable from # 5 to #1 to complete the loop.All switches have the firmware 4.1.0.16I discovered using LanSpeed Test on a PC - that Switch #3...
View ArticleFX2 IOA - any way to turn off default VLAN1 Untagged?
Hi, we are configuring our new FX2 chassis and the I/O Aggregators seem to insist on any port we configure must also be in VLAN 1 untagged:Dell#show vlanCodes: * - Default VLAN, G - GVRP VLANs, R -...
View ArticleHow To Get Out
I am new to the powerconnect family. I have a 6224p and it is working fine. However I have created a couple of vlans 40 (192.168.40.x/24) and 50 (192.168.50.x/24). And I want to now create a route out...
View ArticleForce10 S50N to S55
I just had a quick question....Could you export a configuration file on a S50N switch, and then import that configuration to a S55 switch? Are the configuration files inter-changeable?
View ArticleRunning QnQ in E600
Dear Sir, Currently we are using Dell Force-10(E600) Router. We want to configure QnQ in this router. Can you provide us any help regarding this topic and configuration.Yours sincerelyManis
View ArticleForce 10 E600i Using two Router Processing Modules as different routers
HiI want to know if we can use two Router Processing Module (RPM) in Force 10 E600i as two different routers in place of being redundant RPM modules for each other.RegardsBrijesh
View ArticleVRTX 2401 - VLAN & LAG Configuration
I'd like to configure my VRTX 2401 as follows on my ESXi 5.5 server but am having some difficulty getting the proper LAG & VLAN configuration and hoping someone can help.ESXi 5.5vmnic 0/1 (Internal...
View ArticleTrouble getting voice vlan to work on 6248
I am having trouble getting a new voice vlan to work. The relevant parts of my config are shown below but essentially I am using port 3/g30 for testing and to that switchport I have a polycom voip...
View ArticleCannot telnet to loopback/vlan interface on N2000 (N2048) switch.
I had a N2048 switch connected to our network with an IP address on a vlan with a static default route.I made the following changes to the switch and the switch was no longer available to telnet \ ssh...
View ArticleDell Power Connect 8132F Jumbo Frames Settings lost
Hi,I am using power connect 8132F for my iscsi ESXI 5.5 environment.All iscsi IOs are going through 10 gig only. I have set jumbo frames 9126 and started my work.After some days my jumbo frames...
View ArticlePair of S4810, cannot ping other switch through VLT link
Hello, my topology is following:A <-> S4810-1 <======VLTi======> S4810-2 <-> B \==VLT-HeartBeat=/For some reason I'm seeing flakey connectivity with S4810-2's control...
View ArticlePowerConnect 2808 stuck in loop
I cant seem to get out of a loop. The manged mode light keeps blinking. I have tried the paper clip trick posted here . Still nothing is working. Is there anything i can do?
View Articlecan not connect to power connect 3024
hi,I got a used PowerConnect 3024. it has been reset but I can not access the web interface. it is possible to make the first setup via the web interface or do I have to use the serial interface?Thank...
View ArticleN4032F w/dual power supplies fails to reload
I'm just starting to work w/a new 4032F with dual power supplies (both powered). After issuing a reload command I get this:Reference platform resetting ...syncing filesystems....This may take a few...
View ArticlePowerconnect 3348 stuck at Stand Alone
Hi All, First off I am new to managed switches so go easy on me.I just purchased this unit used and have it connected using Putty through a USB to serial cable. Once the device starts to boot it...
View Article