Clik here to view.
How to identify packet loss and connectivity issue
Hi Support, I'm having packet loss and connectivity issue on my current network. I have 2 core switch (dell power connect 6224 - stack) and all the access switch (power connect 6248) is connected to...
View ArticleDell Powerconnect 6248 Layer 3 - sometimes poor or unanswered pings on vlan...
Hi,i have three 6248 (firmware version: 3.3.13.1) configured as vrrp Gateways, one is master and the others are backup.I have different vlans, all of them are routed vlans.In some cases the vlan...
View ArticleOID for PowerConnect 3548
Hi,I require the CPU and Temperature OID's for a PowerConnect 3548Any help would be appreciated
View ArticleDell Powerconnect 2824 Single port to Multiple Vlan
Hey,I have a Dell powerconnect 2824 Switch and i want to assign Multiple Vlan's to ports 4-12. So, basically i want ports 4-12 be part of 4 different Vlans. The reason is because i want to connect all...
View ArticleX Series Vlan General Port
Hi all,I got some problems with VLAN on a Dell X1026 switch. I configure 4 ports as general ports, with Pvid=50 (tagged with id 50) and member of vlan 50 tagged and vlan 1 as untagged. According to...
View ArticleSwitch blocking ISP traffic?
Hello,We have a 3324 that has two different ISP's plugged into a single vlan that distributes to two firewalls. It's essentially acting as a dumb switch. We had recently upgraded our ISP to a higher...
View Articleshow interface disable cause (N2000)
Dear Expert,If the port-channel is disabled on a N2000 switch, how can we find out the cause of it? Is there any command to show this?Thanks,Sam
View ArticleN2048 dot1x monitor mode issue
I have dot1x working with certificate based RADIUS auth against NPS. For some reason, though, when I turn on monitor mode with the command "dot1x system-auth-control monitor" as described on page 293...
View ArticlePowerconnect M8024-k switch failed as primary switch in M1000e module group A1.
There are TWO switches being used, NOT TRUNKED together, but LAGed together at the CISCO NEXUS switch. The switch in slot A2 is running fine with each M620 blade using dual 10Gb daughter cards for the...
View ArticleDell PowerEdge M1000e - TenGigaBit interface showing 40000 Mbit speed
I all,I got the Aggregators configured as a stack. The uplinks I have configured are Te 0/52 and Te 1/52 and this 2 interfaces are part of a port-channel.Te 0/52 Up 10000 Mbit Full...
View ArticleDell 2848 Radius
Hi,I am trying to enable Radius authentication on an 2848 (to W2k12).I've tried following this guide - http://www.darylhunter.me/blog/2010/06/dell-powerconnect-radius-windows-server-2008-nps.htmlor...
View Articlex1052 management from desk
I have three PowerConnects 2748 where I was able the below in italics so I was able to manage the switches from my desk.http://en.community.dell.com/support-forums/network-switches/f/866/t/19353942"An...
View ArticleIGMP snooping on a stack
Hello,I have 2 N4032F in a stack.The switches are for a VSAN cluster.I want to enable IGMP snooping so I can use them for a 2nd VSAN cluster (in a different VLAN).At the moment I have not set up any...
View Articleconnect sonicwall tz215 with dell 6248p
I'm currently setting up the powerconnect 6248p switch with sonicwall tz215 router. I'm trying to make the switch as simple as possible. The router will do the WAN and DHCP and the switch will route...
View ArticleDell Switch 3524P
dears,are Dynamic ARP protection and IP source guard supported on 3524P or 3548P dell switch and if not on which series are supported and equivalent to 3524P switch.thanks
View Articlestack-mac persistent
Hello all,Our company recently acquired four Dell N4064F switches. We have two in one COLO facility and two in another, both places the switches are in a stack of two acting as one logical switch. It...
View ArticlePowerConnect 5524P - additional name in certificate
HelloSetting up the https certificate on the switch and would like it to have an additional Subject Alternative Name so I can reach connect to it on https://hostname and...
View ArticleClik here to view.
Setting up VLANs on stacked 6224s (iSCSI and LAN)
I have a pair of Powerconnect 6224 switches running in a stacked configuration. Up to this point, I have only been using them for iSCSI traffic, so there was never a need to setup any VLANs, etc. My...
View ArticleCan a Force10 MXL blade handle non FCoE traffic?
Hi. I'm inheriting an M1000e with a couple of Force10 MXL switch blades installed. The chassis has no other 10GBASE-T switches. Since I have no plans on using FCoE, can a Force10 MXL be used for...
View ArticleMulticast in Powerconnect 81xx
Hi,I must upgrade a cluster of switch Powerconnect 81xx from firmware 5.1.0.1 to firmware 6.1.2.4 or higher. This switches stream television in multicast. Could you please help me to configure the...
View Article