PowerConnect 5524P - half the ports went dead
We have several 5524P and some 5548P switches. All of them non-stacked powering up Aruba AP105.We started to replace them today with AP325 and run into problems. This switch has 15 AP105. We replaced...
View ArticleThis Week's 5-Star Enterprise Support Articles
Here are this week's top-rated support articles based on accuracy, usefulness, & ease of understanding: Windows Server: Slow network performance on Hyper-V virtual machines with Virtual Machine...
View ArticleN3000 - Vlan Interface - NO description option available
Folks,Can you please advise if this is by design or if this in an 'unintended feature'?I am in the process of migrating a config from a cisco switch and not having the ability to label the various...
View ArticlePower Connect 2724 Loud Fan
Hello,The fan in our Power Connect 2724 has become very loud.Is there anything we can do to remedy this? We're concerned with it overheating.Please advise.Thank you,Sharon
View ArticleSet up Voice/Data VLANs on ports, Voip works but Data doesn't
I followed the guide to set up a switchport in General mode on my N2048P to support voice and data vlans on the same port. My IP phones will get a DHCP IP address and I can make calls, however, data...
View ArticleForce10/DELL S60n shows PSU in bay 1 as absent even after replacement.
Hi thereI have two Force10 S60n's and after a power surge a few weeks back I have some issues with one of them. It's somewhat mysterious so bear with me here.Over snmp it reported: Status Alert: s60-01...
View ArticleDELL N1524 and OME
I have a stack with two N1524 (firmware version 6.3.0.18) and on a server OME (versione 2.2.0.2056)in the devices list i have 2 host with IDRAC Enterprise and a Compellent Scv2020 with a green icon but...
View ArticleDell PC5548 problem with connection to Gallagher 6000 Control Module
I have a Dell PC 5548 in my production environment. I am attempting to connect a Gallagher 6000 Control Module for our security system. I can see there is traffic on the port, however, the control...
View Articleconditions for Vlan IP to be up? PC 64xx
when does an IP of a Vlan go & stay UP? How does a switch decide when to take and keep it down?regards
View ArticleN1548p Reformat file system ?
Hi,Yesterday my N1458p only shows the boot menu and can't load the image, should I try reformat and restore file system option ? Any recovery guide you recommend ?Best Regards.
View ArticleStuck at pinging out of vlan on S3048
Hi. trying to get started on setting up a new network with a S3048 as the core switch. As a starter i've created a vlan - id 100. This has been assigned to port ge 1/1. Connected to this port i have...
View ArticleHow to enable Internet access for VLAN's.
Good day,I have 1 Dell Switch 6224 , with 2 VLAN 's configured , VLAN 400 and VLAN 500, but can not access the Internet .VLAN400 : 192.168.3.1/24VLAN500 : 192.168.2.1/24Default gateway IP :...
View Articledynamic VLAN assigemnet 802X PowerConnect 6248P version:3.3.12.1
Dynamic VLAN assigemnet 802X does not work with nps.on port 1/G17 i would like to use dynamic VLAN assigemnet.We have nps server.Radius client is doneAlso connection request policiesand network...
View ArticleN4032 two switch vrrp
Hi,There is a firewall and two n4032 switch connected to unmanaged flat switch. the vlan 5 used for two switch vrrp. the switch 1 is taking as master , but switch 2 is always showing initialized...
View Articleif a port-channel is in a Vlan do I need to manually-specifically put its...
from standard Vlan configuration point of view.?regards
View ArticleM1000e Port-channel problems
I've got an m1000e with (2) M I/O aggregator cards (slot A1 & B1) cabled via the 40g ports to (2) S6000 switches set up in VLT mode. I am using the default port channel (128) and ports 33-40 on...
View Articleto make management interface out of reach - 62xx
dear everybody,how to configure and access management interface if Vlan which is exposed, connected to the rest of net outside the stack (where from one would be hoping to access that management int)...
View ArticleDELL PowerConnect 5548 factory reset using Telnet
If someone has the time could they please step me through the process of getting into the CLI to do a factory reset of a PowerConnect 5548? Never used Telnet, but I just enabled the feature in Windows...
View ArticleDell Force10 S4810 access port question
Hi all,I need to pxe boot servers from a pxe/dhcp server and all of them are connected to S4810. Previously on powerconnect switches I had make the ports access port to specific vlan in order make pxe...
View ArticleBuy Registered IELTS,TOEFL,Certificates,Passports,Drivers License,ID...
Buy Registered IELTS,TOEFL,Certificates,Passports,Drivers License,ID Cards,Visas,We offer our exclusive clients the ability to gain IELTS,TOEFL,ESOL AUTODESK certificates without taking the exams. The...
View Article