Powerconnect 8024K blade switch to vsphere vswitch ?
Good day to AllI have a stacked pair of PE 8024 blade switches, a 10gb interface from each (eg. Te1/0/1 and Te2/0/1) presents to a pair of NICs on the physical side of a vSwitch (I have 4 hosts...
View Articlepowerconnect 2824 VLAN
Hello everybody,It is the first time i have to configure a Dell switch and I have trouble setting up my VLANs.I need 3 VLAN:VLAN1 : internet connected with a router for the internet accessVLAN2 :...
View ArticleDell PowerConnect 8024F CPU OIDs
Hi,I've read a post on this site which suggested these OIDs: .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.3...
View Article2 N3024 switches VRRP Config questions
First question is that on both of my switches, there is one vrrp address that both switches take master state on, I've tried reloading both switches and I'm not sure why, all of the other vrrps will...
View ArticleHTTPS on N-series (blank certificate)
Hi,On N3000 with 6.3.1.8 OS I tried to set up HTTPS web management access, with following commands:(config)# crypto certificate 1 generate(config-crypto)# key-generate <---- just default...
View ArticlePower Connect 62xx - sflow Sampler limits
Is there a firmware version that has addressed the 'Maximum Samplers Limit exceeded' error when 32 are reached? I have stacked 48 port switches and would like to have all ports set.
View ArticleDell Switch N2048 Inter Vlan Routing
Dear all ,I am facing a issues in N2048 switch , we have created a multiple vlan in switch , but we are unable to communicate from vlan to other vlan .Running configuration is as attached .please...
View ArticleGeneral Mode Vs Trunk Mode
Hi All,I apprecaite General Mode is more flexible when interconnecting two Dell switches.However, is it preferable to use trunk mode when interconnecting a powerconnect to a different vendor switch or...
View ArticleInter VLAN routing with multiple VLANs
Hi Everyone,I have just inherited my first Dell PowerConnect 6224, and I have been trying to configure VLANs on it with intervlan routing but i've gotten too frustrated with it. What I'd like to...
View ArticleN2000 SSH Connections
Our network consists of N2XXX, N3XXX, and N4XXX switches. We would like to remove telnet access from all switches and use SSH. What commands would I need in order to initiate a SSH session from one...
View ArticleN2048 management access over VPN
I have a N2048 that I can access while on the physical network but I cant access it over our VPN tunnel. I can access all other devices on the same vlan / ip range that the switch management resides on...
View ArticleUnable to see world from VLANs - N3024
I recently made a similar post, but had to change the config to include VRRP and now I'm back to where I was before.Vlan 309 serves to connect between this switch and our firewall (asa 5525-x). If I...
View ArticleSetting up a VLAN on PowerConnect 3548P
Can someone help me to set up a VLAN on a 3548P please? My understanding of VLANs is fairly high-level so I need help with the detail of the configuration as I've never done it before.This is what I...
View ArticleUnable to tftp on Dell N3024
Trying to update firmware on Dell N3024 switch. Syntax is correct but when it executes the transfer I get the transfer failed error. Also tried by USB port and get the USB not detected error. Is the...
View ArticleESX, 8024f and my multicast nightmare
console#show run!Current Configuration:!System Description "Powerconnect 8024F, 4.2.0.4, VxWorks 6.6"!System Software Version 4.2.0.4!Cut-through mode is configured as disabled!configurevlan...
View ArticleDell PowerConnect 6248 LAG Dropping Connection
We are currently having some issues with our Blade Server LAG connection. The error we receive is "0/3/1 is transitioned from the Forwarding state to the Blocking state in instance 0". This happens and...
View ArticleDell Networking X1052 cancels all configuration to factory default after...
Why our Dell Networking X1052 cancels all configuration to factory default after power off?Is it right? So, if the power off, I need configure switch again after power on?
View ArticleMS NLB, Dell 8024f and my multicast nightmare
I'll keep this short as there isn't a lot to it. I have an ESX cluster (8 servers) connected to a 8024f. There are 2 vlans that the ESX cluster operates on, I am able to connect to both of them from my...
View ArticleDell PowerConnect 5448
Hi all.I have some question.I have unknow mac adress on port this switch. I do not know who owns this address. How I can get ip adress this device?
View ArticleN3024F transceiver Dell Part# : 407-BBOR
Hi Guys,This could be an old issues, but I need help on the speed configuration for this DELL transceiver installed on DELL Powerconnect N3024F switch.I have 2 x network industrial device with...
View Article