conection 2 5548 stack switch with 2 stack 3348 siwtches
I need help with connect core stack 5548(2 switches) with multi vlans with 2 stack switch has 1 gb ports and SFP 10bgibit link, 3548 switches have just 100 ports, g1-g2 - 1gibit ports , port g3 and...
View ArticleDell PowerConnect 6024 lost passwd
Hi all!Please help.I have 6024, but password it lost.How do I reset the switch to factory defaults, and what will be the password to edit?
View ArticleClik here to view.
LAG not working following after following Switch Configuration Guide for...
We are using the information provided from the following document: i.dell.com/.../dell-networking-n4000-series-switch-configuration-guide-for-equallogic-sans.pdfWe have two N4032F switches that are...
View Articlemultiple vlans on 1 port is general mode the right way?
We are setting up n3048. We do have 3 vlans 2 ports in a vlan 999 wich is connected to the other networks as the uplink. Our subnets are routed to this vlan interface. Internal we have 2 vlans: vlan 10...
View ArticleEncryption for RADIUS key?
On the N-Series switches, the radius key is, by default, shown in plaintext in the configuration file.There's an option via CLI to specify an encrypted value, but it says the parameter length should be...
View ArticleClik here to view.
redundancy on core switch
Hi all,We are going to implement redundancy at core level in which we will have two firewall and two switch in failover state as shown belowI will be using Sonic wall so we can configure high...
View ArticleForce 10 S50 Load balancing with 3 Internet Lines
Hello,I have 3 50MBit/s Internet Lines. How can I use this 3 Internet Lines parallel for all connected Clients (load balancing)?
View Articlex4012 MTU for VMware NSX
Hi,I am looking for two cheap 10Gb switches without high-end perfomance to create an NSX demo environment. VMware NSX has only one hard requirement and one optional for full integration.Would a Dell...
View ArticlePowerConnect 2848
Hello, I started working in this new company where they have 2 esxi servers in which there are a couple virtual servers and they are connected through the powerconnect 2848. The issue which I am having...
View ArticleRouting & non-Routing VLANs on the same switch
Hi: hope anyone can help me... I have a 6248 Powerconnect L3 switch with 5 VLANs. All VLANs route packages to each other. Now I have to create a new VLAN that don´t route to the other VLANs, even to...
View ArticleN4000 - ESX - Route based on iphash only working with 1 link
I'm trying to get a normal etherchannel working between ESX (Version 6) and a N4032F Stack.I'm using 2x 10Gb/s links. After connecting the second link and waiting 3-4 seconds the host can't be pinged...
View ArticlePort Stuck
I have a problem with a switchport on an N2048P. The port is not working anymore. This is my test port. The last thing I did, was reconfigure it from trunk to access while it was up. After that the...
View ArticleDell N3000/N4000 MIBs for snmp monitoring
Hi,we use PRTG for monitoring and it has built in sensors for Cisco, HP, Juniper but not for Dell.Where can I get the latest mib files?Thanks!
View ArticleSupermicro X8SIE motherboard IPMI LAN port will not work with PowerConnect...
I have two Supermicro systems connected to a PowerConnect 2816 switch. Both have dedicated LAN ports for IPMI management of the systems, but only the newer one works with the 2816. Interestingly, the...
View ArticleStacking different models of PowerConnect ?
Hi! everyone,I would be most grateful if anyone can let me know if it is possible to stack a PowerConnect 5524 with a 3548, (the 3548 do not have a HDMI port, only gigabit ports for stacking) if yes...
View ArticleAny hardening Guide for Dell Switch
Hi,Anyone have the hardening guide or checklist for Dell switch?Thanks.
View ArticlePower Connect 2848 - user authorization with IP address
Hello,I have set up the local username and password to limit access at Power Connect 2848. Did any method for this model which can enhance the access protection such as IP address, VLAN or port...
View ArticleConnecting RPS720 External Redundant Power Supply to DELL 5548
HI, We have two DELL 5548 network switches.As per the switch manual, we can buy the RPS720 External Redundant Power Supply connecting to current DELL 5548 network switches to achieving the redundant...
View ArticleN2048P : Update to Enable password not taken into account
Hi,I try to update the password of my N2048P stack for Enable account by logging in as an asministrator, then going to General > Management Security > Enable PasswordNo error is shown at apply +...
View ArticleDell PowerConnect 6248 SFP Issue
I have a issue connecting PC6248 SFP port, any SFP front port to R710 (Windows 2008) using a bcm57711 net card. The port show no LED OnI was able to connect the PC6248 via SFP to another Dell Switch...
View Article