switch config with tagged and untagged vlans
We have an N1548P switch which connects to a number of splicecom phones. Our PCs plug into the phones. Therefore the phones and PCs are sharing a switch port. Currently everything is in vlan 1.We'd...
View ArticleZ9100-on remove one PEM don't have alarm
Hello,Why there is no alarm when I remove one of the PEM on Z9100-on?There is PEM removed log, and automatically cleared as below.TORSWA02(conf)#Sep 23 00:14:37: %STKUNIT1-M:CP %CHMGR-5-PEM_REMOVED:...
View ArticleDell 55xx will not connect via SPF+ ports.
I am trying to connect a Dell 5524 with a Dell 5548 over a 350 foot fiber connection. I am using a pair Dell Networking, Transceiver, 10GbE SFP+ LRM Optic, 1310nm Wavelength, 220m reach on MMF - Kit's...
View Articlemultiple shutdown / up message on 6 SW stack?
Hello,Does someone know how tro read these error reported in log from a 6 switches N2048?We experience some network performance problem and would like if it could an indication?Our current firmware is:...
View ArticleConnecting two N3000 stacks via SFP+ ports
I have an N3000 stack and I am planning to connect it to another 2-stack of the same model. I want to connect using two fiber channels, so both SFP+ ports on the 2-stack will be taken up. I assume for...
View Articleadd port to VLAN gets error wrong length
Hi,I have upgraded my Powerconnect 2848 to the latest firmware: 1.0.0.45 and since that I have the issue when I try to add a port to a VLAN I receive an error" null" with the description "wrong...
View ArticlePowerconnect 5324 after upgrade firmware still show 2006 firmware
Powerconnect 5324 after upgrade firmware still show 2006 firmware .and please guide step by step how to update firmware or boot in advance Thanks .br aukonline
View ArticleClik here to view.
Need help to control broadcast
Hi,I am using Dell Powerconnect 5324, I want to configure my switch to control the broadcast, When I tried to check broadcast on default settings at port g1 its controlling the broadcast but it's...
View ArticleWill NetApp Storage is compatible with Dell Force10 S60
I have Dell Force10 S60 Switch purchased on August 2015 and warranty going to end on August 2018. This Year we are purchasing NetApp storage, I want to know whether NetApp storage is compatible/support...
View ArticleHyper-V Failover Clustering and Nic Teaming - Target Storage is SMB3
All,I'm Using a 8024F pair in Stack mode with 2 hyper-v Hosts that connect to a SMB3 Storage for hosts:Switch config is the following on each Server:Hyper-v1: Dual 10GB card (Nic Team LACP/Hyperv...
View ArticleReplace failed M8024, not stacked, Module B1
I need to replace Mod B1 10GbW XAUI. Device becomes primary when plugged into chassis, bad. Remote location and I have access to CMC. Looking for steps to replace, put IP on it, restore backed up...
View ArticleReset SNMP port status
We have a dell 6224 switch which is being monitored using SNMP. One of the servers connected to that switch was turned off as we don't need it anymore. Now the switch SNMP engine says the status of the...
View ArticleDHCP snooping between multiple switches and how to make exceptions
I am using two Dell S4810 switches which are connected to a router S6000.The issue that I am experiencing is that DHCP requests can't be delivered from DHCP server on sw1 to DHCP client server on sw2...
View ArticleWhat switches can do VLT Peer Routing?
Can the Dell S60 do VLT Peer Routing? What switches can do this?
View ArticleSmart Switch software
I have a Samsung Galaxy S7 smart phone. Before the phone undergoes a factory reset, I need to download my contacts, pictures and videos to my laptop. To download I need to use Smart Switch software....
View ArticleDell switch Multiple vlan's switch ip not communicate
HI Team,In my Organization we recently implemented multiple vlan's on Dell powerconnect 6428 switch,all vlans communicated properly, The only thing is if assign any ip on switch it can't...
View ArticleEnable SSH on Dell Power connect 2848
I have a dell power connect 2848 and I am looking to enable ssh on it. I have tried following the below instructions but they all error out for me except the config command but i can still make no...
View ArticlePowerConnect 3524 Can't Access Web GUI
Hello,We have an older 3524 switch that we recently reset and need to configure from scratch. I am able to telnet into the switch with putty and I deleted the startup config and reset the switch. I...
View ArticleErratic Connection Issue's
Dell PowerConnect 2748.Firmware: 0.00.33 (2007)Bootcode 0.00.5 (2007)Symtoms:No active connection when exited 'managed mode When IN managed mode, switch works.When connected Cisco NSS 4000, 1Gig link...
View ArticleDNS Issue with PC6248
Hello,I am having an issue with name resolution on a PowerConnect 6248 specifically around the SNTP function. I have taken the switch down to a very basic config; no VLANs , no routing, just basic IP...
View Article