Clik here to view.
3548P Status question
Hi,I have a 3548P that went through a lightning storm last night and now the status under the GUI for the PoE section says faulty. It looks like the rest of the switch is fine however, our PoE phones...
View Articleis it possible to create PortChannel on PowerConnect 8164 switches to SFP Ports?
i want to know, if could be formed PortChannel between two Dell Switches PC8164 on SFP Ports.Regards!
View Article3548P configure a network printer
Back again with a new question...I recently inherited our network at a small college prep private boarding school. The network was configured by an outside company many years before I arrived. There...
View ArticlePowerconnect 62xx VLAN Routing woes
Hi guys,I'm having alot of difficulty trying to configure what I thought would be a very basic VLAN exercise, I'm in dire straits and could use some sage advice.Basically I'm installing a new voip...
View Articleconnecting m8024-k switches to cisco 5k
We have two m1000e blade chassis, each with 2 m8024-k switches. We are using this document (see link below) to connect them to four cisco 5k's....
View ArticleHow to customize OSPF Timers in Dell PowerConnect 8164
Hi there!on Cisco router, this could be done in this way:interface FastEthernet0/0 ip address 3.3.3.2 255.255.255.0 ip ospf hello-interval 10 ip ospf dead-interval 20How to do this customization in...
View ArticlePowerConnect 5524 with 3rd Party Optics
We are using Champion One 10KM and 40KM BIDI (single fiber) 10GB optics (10GSFP+) in Dell Powerconnect 5524Switches (firmware 4.1.0.10). We are running the switches in stacked pairs withan optic in...
View Articlehow to use Ssh and Https to PC8164 PC5524
hi there!How to use SSH and Https to connect to PC8164 and PC5524?Regards!
View Articlenic bonding through 2 unstacked 6284 switches
Hello,I'm trying to connect a server (on linux, using two NICs) through 2 unstacked powerconnect 6284 switches, for redundancy. I'd like to use balance-alb mode on the linux bonding driver, but for...
View Articlecould osfp run on portchannel in PC8164
i'll connect two PC8164 switches with fiber optic to SPF modules:i've want to create portchannel to to these SPF ports, and this could done, right?so my question is:Can i put IP interfaces to this...
View Article10Gig interfaces with 6248
I have a 6248 with two CX4 interface modules installed. I want to connect to a fibre using one of the SFP slots. Do I have to remove one of the CX4 modules before the SPF port becomes available for...
View ArticlePowerConnect 2848 and VLANs for wireless only
Hello, I have the following setup and am new to VLANs. Managed mode is enabled on all of the switches, but right now nothing else is configured (aside from the password and IP).Wiring closet 1Sonicwall...
View ArticlePowerConnect 3424P - The server at XX.YY.ZZ.AA is taking too long to respond
I get this message when I try to use the web interface on my 3424P switch. I executed the "ip https server" command and created an administrator username with level 15 access using the terminal...
View ArticleDell 6224 Class of Service Setup
We have several Dell 6200 series switches running 3.3.5.5. We are putting in several Avaya G430 Gateway units at various locations and are attempting to configure the switches to utilize Class of...
View ArticleClik here to view.
Could i use Dell SFP modules MultiMode to Fiber optic Single mode?
I've this modules of SFP model FTLX8571D3BCL as in pictureThis model is multimode, as i see in this link:http://memorydealers.com/transceiver/sfp-1/ftlx8571d3bcl-dell-original.htmlbut the fiber is...
View ArticleDell Power Connect 5524; 5548
HelloCan anyone advise me what the optimum temperature needs to be in Comms Rooms where Dell Power Connect 5524; 5548 are running?Is there a minimum and maximum temperature?ThanksLois
View Article6248 Stack Issue? (Config Included)
Hi Folks,First of all, I am 100% new to the Dell switching model. Secondly, I've only been with this company a month and have been putting out more fires than any individual my age should have to!My...
View ArticleTrunk with Etherchannel
Hello all,I have an environment with two switchs, Dell and Cisco, and one firewall, I put the firewall as a bridge with etherchannel and trunk, and different Vlans on each side, it looks like...
View ArticleStacking Module - Dell Powerconnect 6248
Hello. I have a Dell Powerconnect 6248. This used to be a secondary switch in a stacked configuration (2 switches total). However, the master went down in a power outage so we unplugged it and this one...
View ArticleMulticasts from PowerConnect 55xx's.
I will try and explain this as best that I can. I have several non-dell devices who are reporting back via syslog an error similar to this:Jul 23 11:11:37 ap01 id=firewall time="2013-07-23 15:09:54"...
View Article