Dell 6224 versus Dell 5424 Init Files
Hello. I updated my Dell 5424 Init file to run on the 6224 however I still cannot access the GUI (even after allowing http). I tried to route the managment port per a previous suggestion but that did...
View ArticleSystem is currently in a master-only mode
How to really reset my factory 5524.I have done a reset but the message "System is currently in a master-only mode" continues
View ArticleTrying to get a LAG between a 5524 and a 5424 to act as a trunk.
interface 1-2 are configured as port-channel 1 on both switches.5424interface range ethernet g1-2channel-group 1 mode auto5524interface range gigabitethernet 1/0/1-2channel-group 1 mode auto5424...
View ArticleW-650 Controller and web blocker
have a W-650 setup with a company wireless SSID and a guest SSID. Need to put IP address of Web blocker in it to keep people from surfing where they shouldn't be. Called Dell and the tech didn't know...
View ArticleUpdate firmware on S4810
hi there,We have been experiencing intermittent network problems and I was wondering if our s4810 switches could do with a firmware upgrade. I can't find much info on what the latest firmware version...
View ArticleHigh latency on Dell 5524 stack
We have 2 x Dell 5524 switches configured as a stack. Only 8 ports are in use on each switch (5 of the ports are used for the same servers which have two NIC's configured as a team set failover...
View ArticleDell 3348 Fatal Error - return: -3 bcm_cm_device_supported failed
Hy to all. In this morning i get this message by console. Since then about a year all was ok. What this can be and how to repair. In case his firmware one how to restore. Below is the message. Hope...
View ArticleEnable SNMP for S5000 Switches
Hi, I have tried all the commands related to the SNMP in the S5000 Dell Force10 switch, but I'm not able to allow ManageEngine OPManager to detect it switch. snmp-server community "public" ro...
View ArticleN4032 Network Switch.
Hello to all,The N4032 Switch is openFlow ready and if yes, up to what version of openFlow?Is there an update that should be used?Please find below relevant info.CPU Version..........................
View ArticleTransfer settings from PowerConnect to N3000
Hello,I am trying to copy paste the settings we currently run in a PowerConnect 6448 to a new N3048.Sadly seems like lots of commands don't use the same syntax they were used to have. The CLI...
View ArticleClik here to view.
PC 6248 VRRP problem
That is my diagram, and my problem is that:When I turn off the PC6248_01, the 6248_02 immediately become VRRP master, but it lost the connection to other VRRP node in about 30s(on 6248_02 I can ping to...
View ArticleMTU Sizes Jumbo Frames
I have a few questions on how the PowerConnect 6248 handles MTU sizes:1. It appears if I have a host using jumbo frames at 9000 MTU then I have to use a MTU of 9216 to match?2. I can apply a MTU...
View ArticleQuestions related to VLans
Hello,i have to setup one of our Dell Poweredge 7024 switch in front of our network, and i'm not a network specialist ...But, a friend told me that we can "split" this switch in multiple switches, so...
View Article6224 no console activity / how to use reset button
I have a pair of 6224 switches stacked. A power loss rendered member 1 (master) unresponsive. member 2 took on role of master and booted fine. Member 1 has Master light on as well as Power and Fan but...
View ArticleMXL 40/10
Hello All,We are going to upgrade firmware of our switches and my question is that anyone can share link to download latest FW 9.6.0.0, Many thanks for your help
View ArticlePowerconnect N4000 management authentication radius via OOB
Can this be done?So far I've only managed to get it working via an SVI interface. If I do not have any SVI interfaces and only the OOB interface configured, trying to login with RADIUS methods over the...
View ArticleDell N3024 - Configuring a user with a subset of privileges
I am new to the Dell switches. I have created a username and assigned an admin-profile to give the user a subset of commands that the user can perform.I would like to configure the switch so that...
View ArticleBlade switch MXL 10.40 upgrade
Hello AllWe are going to perform upgrade of all our switches to latest firmware 9.6.0.0Is there any needs for usb drive to make it avaiable for switches access?Also do you know how long can take...
View ArticlePoweredge VRTX brings down network
Has anyone ever experienced this before? We have 2 dell force 10 switches in our infrastructure and we just recently purchased a Poweredge VRTX with 2 blade servers for our environment. We installed...
View ArticleMIB for Port Security Violation in Dell 5548P
Hello,Can anyone please help me to findout MIB's or MIB value for Port security violation in Dell 5548P switches. For Cisco switches they are saying [1.3.6.1.4.1.9.9.315.0] MIB value will work for the...
View Article